User manual IOMEGA 6400LTO

[. . . ] SuperLoaderTM Automated Tape Library User Manual 81-81178-01 A01 Ver. 01 SuperLoader Automated Tape Library User Manual, 81-81178-01 A01, Ver. This publication is provided "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. This publication may be revised from time to time without notice. [. . . ] If you try to unload a cartridge from the drive while the SuperLoader is writing to the tape, the command will not be initiated until the write command is completed. Insert a Single Cartridge 4 When you want to load a single cartridge into the SuperLoader, you can use the mailslot. However, if the Security option is turned on, you have to enter a valid password to unlock the mailslot before you can load a cartridge. When you insert a cartridge through the mailslot, you can load it into the tape drive or store it in a magazine. To Insert a Cartridge to the Tape Drive: 1 On the main menu, scroll to Commands, then press Enter. 2 On the Commands submenu, scroll to Enter, then press Enter. 4 SuperLoader Automated Tape Library User Manual 75 SuperLoader Operation Front Panel Functionality 3 On the Enter submenu, scroll to To Drive, then press Enter. Note: After Load cartridge appears on the LCD, a countdown appears. You have 20 seconds to load a cartridge through the mailslot before it re-locks. For the SuperLoader DLT, push in the cartridge until you meet resistance. The cartridge will be about two inches (5. 0 cm) inside the mailslot, and only the end of the cartridge will be visible through the mailslot door. For the SuperLoader LTO, push in the cartridge completely. The door cover drops and lightly taps your fingers when the cartridge is inserted completely. Note: Figure 52 Loading a Cartridge (SDLT Tape Shown) 76 SuperLoader Automated Tape Library User Manual SuperLoader Operation Front Panel Functionality 4 Once you have inserted the cartridge, the prompt Enter to Continue appears. You have 20 seconds to press Enter in response. Note: If the insert cartridge function fails, the cartridge ejects and you will have to perform steps 3 and 4 again. To Insert a Cartridge to a Magazine Slot: 1 On the main menu, scroll to Commands, then press Enter. 2 On the Commands submenu, scroll to Enter, then press Enter. 3 On the Enter submenu, scroll to To Location, then press Enter. 4 A map of all the magazine slots appears. Slots that are occupied by a data cartridge are indicated by an asterisk (*). The slot that is occupied by a cleaning tape is indicated with an @, if AutoClean is enabled. 4 Scroll to the slot where you want to store the cartridge, then press Enter. After Load cartridge appears on the LCD, a countdown appears. You have 20 seconds to load a cartridge through the mailslot before it re-locks. The SuperLoader automatically loads the cartridge into the selected slot. Note: If the load cartridge function fails, the cartridge ejects and you will have to perform steps 3 and 4 again. 5 Once you have inserted the cartridge, the prompt Enter to Continue appears. You have 20 seconds to press Enter in response. Move a Single Cartridge 4 You can easily move a single cartridge from one location to another inside the SuperLoader. SuperLoader Automated Tape Library User Manual 77 SuperLoader Operation Front Panel Functionality To Move a Single Cartridge: 1 On the main menu, scroll to Commands, then press Enter. 2 On the Commands submenu, scroll to Move, then press Enter. The Move screen appears Under From:, scroll to the current 4 location of the cartridge you want to move. Slots that are occupied by a data cartridge are indicated by an asterisk (*), then press Enter. 3 Under To:, scroll to the location to which you want to move the cartridge. [. . . ] A protocol that SNTP Simple Network Time Protocol. SNTP is based on NTP, the Network Time Protocol, an industry standard way for computers to synchronize their time to an external reference standard. Each consists of a client, for 212 SuperLoader Automated Tape Library User Manual example the SuperLoader, which obtains the current time (in UTC) from either an SNTP server or an NTP one. SNTP and NTP are in wide use on the Internet. [. . . ]