User manual IOMEGA EXIMAC

[. . . ] Also, changes or modifications to the electronics or enclosure of this product must be expressly approved by Iomega; otherwise, the user's authority to operate the equipment may be voided by the FCC. SCSI SCSI SCSI SCSI SCSI Canadian DOC Information This digital apparatus does not exceed the Class B limits for radio noise emissions from digital devices as set out in the Radio Interference Regulations of the Canadian Department of Communications. Iomega's Automated Help Systems Internet Home Page: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . http://www. iomega. com America OnlineTM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Keyword: Iomega Microsoft Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] All other product and brand names are the property of their respective companies. for Macintosh EN137104 Printed on recycled paper 1 GB Part 15, Class B, of the FCC Rules, is designed to provide reasonable protection against radio and television interference in a residential installation. Although the equipment has been tested and found to comply with allowed RF emission limits, as specified in the above cited Rules, there is no guarantee that interference will not occur in a particular situation. Interference can be determined by turning the equipment off and on while monitoring radio or television reception. The user may be able to eliminate any interference by implementing one or more of the following measures: · Reorient the affected device and/or its receiving antenna. · Increase the distance between the affected device and the computer equipment. · Plug the computer and its peripherals into a different branch circuit from that used by the affected device. Installation Guide drive ® 2 Jaz "tools" Disk (contains Jaz Tools software) Jaz Drive 50HD to 25D Cable Converter External Power Supply Manuals and Install Diskettes* Data Cable * You will not need an install diskette to install Jaz Tools on your Macintosh. 1 WARNING Always turn off power to the computer and all devices connected to it (such as printers or drives) before beginning any computer hardware change. Shut down your Mac, turn off all connected devices, and pick up the Jaz data cable. Unpack the Jaz drive and accessories. This guide shows how to install the portable SCSI Jaz drive on a Macintosh. If you encounter any problems while installing your Jaz drive, refer to the "Troubleshooting" section in the Jaz User's Guide. GB 4 3 Jaz Connector To Remove the Jaz Data Cable: Squeeze the spring locks on both sides of the data cable connector while pulling on the connector. Use the 50HD to 25D cable converter to connect the other end of the data cable to the built-in SCSI connection on your Macintosh. Connect one end of the data cable to either SCSI port on the back of your drive, and PUSH until connector locks into place. (If the connector PowerBook Users You need a special PowerBook cable to connect the Jaz drive. Check with your Iomega dealer or call Iomega at 1-800-MY-STUFF to order a Jaz PowerBook cable. does not go on easily, try turning it over. ) CAUTION DO NOT attempt to stand the Jaz drive on its side!NEVER move the drive when in use! SC 4 SI ID rm Te I A O PW R 0 I SC 4 SI ID rm Te I A O PW R 0 I (Open up for Step 5) 1 5 OPTIONAL: You can connect other SCSI drives to the Jaz drive using another SCSI cable (usually a high density 50 pin to 50 pin cable). If you are connecting the Jaz drive to an existing SCSI chain, you may need a different cable or converter. Call your Iomega dealer or 1-800-MY-STUFF to order. 9 Gently insert the 1GB "tools" disk into the Jaz drive. The amber data light on the Jaz drive flashes as the disk spins up and glows steadily while it acquires. When the amber data light goes out, the drive is ready to use. CAUTION Never put anything except Jaz disks into the Jaz drive as this could damage your drive. Always keep your Jaz disks free of dust and debris. To Another SCSI Device I PW R 0 rm Te I A O Disk shown fully inserted 4 1 1 SC G B SI ID to ols B G To Computer or Previous SCSI Device Disk Eject Button Disk shown ejected from drive 6 Check SCSI IDs if you have a SCSI chain. Each device in the SCSI chain must have a unique SCSI ID. If you have no other devices, the factory setting of SCSI ID 4 should work. If you need additional information, refer to "SCSI Guidelines" in the Jaz User's Guide. SCSI Termination Your Jaz drive is set to handle SCSI termination automatically. Refer to the Jaz User's Guide if you need additional information. Ejecting Jaz Disks The disk eject button is disabled when the Jaz disk icon appears on the Macintosh Desktop. To eject a Jaz disk from the Desktop, use Put Away from the File menu or drag the disk icon to the Trash icon. Note that the drive takes a few seconds to spin down and eject the disk. 10 11 12 Start your Macintosh. Important Make sure the 1GB Jaz "tools" disk is inserted before starting your Macintosh. 7 Connect the external power supply and turn on the power switch. CAUTION Use only an approved Iomega Jaz power supply. [. . . ] Make sure you hold down the Shift key until you see the message indicating that extensions are off or disabled. If the Iomega Tools disk icon still does not appear, recheck the instructions in this Installation Guide. Make sure the Jaz drive is correctly and securely connected to the Mac. [. . . ]