User manual IOMEGA REV 35GB CHANGING BEZEL

[. . . ] . 15 Troubleshooting the REV Internal SCSI Drive. . 16 2 System Requirements The following are the minimum system requirements for using a REV drive. Supported Operating Systems · Windows XP (Home and Professional) · Windows Server 2003 (Standard and Small Business Editions) · Windows 2000 Professional (SP3 and SP4) · Windows 2000 Server (SP3 and SP4) · Windows 2000 Advanced Server (SP3 and SP4) Hardware Requirements · 333 MHz processor, or higher · Available 5. 25" or 3. 5" drive bay · Available internal power connector · 4X CD-ROM drive to use the Solutions CD · 100MB hard drive space · 128MB RAM Additional Hardware Requirements for REV SCSI drive · SCSI adapter card (68-pin SCSI only) 3 ATAPI Installing the Iomega REV Internal ATAPI Drive 1 2 Install the REV System Software. [. . . ] NOTE: See the "About the REV System Software" section of this guide for more information. Disconnect the power cord, and remove the cover to your computer. Verify that the REV drive jumper settings are set to Cable Select as shown in the illustration. NOTE: If you will be connecting another drive to the REV IDE data cable set the jumper settings for that drive to cable-select. 4 3 Locate a vacant drive bay (5. 25" or 3. 5" drive bay) and remove the panel cover. NOTE: If you are installing into a 5. 25" drive bay, you will need a mounting bracket (available from your computer retailer). ATAPI 4 Connect the black connector of the IDE data cable to the back of the REV drive NOTE: For best performance, use the cable that shipped with the drive. 5 5 ATAPI Connect the blue connector of the IDE data cable to the secondary channel on the motherboard and the gray connector to another drive (optional). NOTE: If the secondary channel already has a cable attached, replace with the IDE data cable as shown here or see the User's Manual for detailed instructions. 6 Connect a spare power supply cable from the computer to the drive. NOTE: If there is no spare power supply cable, you may need to purchase a Y-cable power adapter. 6 7 Replace the cover, connect the power cord and restart your computer. ATAPI 8 Confirm that your drive appears in the list by selecting Yes, and then select Close. NOTE: If the detection software does not startup or you do not see your drive listed, refer to the user's manual on the CD for help. 7 9 Native ATAPI GB B / 90 35G/Compressed Insert a disk and your drive is now ready to use. The REV drive icon will display in My Computer or Windows Explorer. NOTE: If this package did not include a REV disk, you will need to purchase one. Iomega REV Internal ATAPI Jumper Settings Cable Select (Default) Slave Master 8 Installing the Iomega REV Internal SCSI Drive 1 SCSI Install the REV System Software. If the file system does not appear as REV UDF, make sure you have correctly installed the REV System Software and rebooted your computer. If you have already installed the REV System Software and this problem occurs, use the Windows Add or Remove Programs utility to uninstall the REV System Software, then reboot your computer. Reinstall the software and reboot again. If the REV UDF file system is still not recognized, there may be a conflict with CD/DVD creation software on your system. Make sure that your CD/DVD creation software is up-to-date. Troubleshooting the REV Internal SCSI Drive Most SCSI installation and performance problems can be resolved by following the same five basic steps: 1. Verify that the REV System Software is installed. This software includes drivers required for REV drives. To verify that this software is installed on a Windows PC, click Start, All Programs, Iomega, and REV System Software. [. . . ] This software includes drivers required for REV drives. To verify that this software is installed on a Windows PC, click Start, All Programs, Iomega, and REV System Software. If the REV System Software folder is not in your start menu, the software is not installed. [. . . ]