User manual IROBOT BRAVA 380T

[. . . ] Braava ™ Floor Mopping Robot 300 Series Owner’s Manual global. irobot. com Welcome Dear iRobot® Braava™ Owner, Welcome to the world of iRobot. As an owner of the iRobot Braava Floor Mopping Robot, you join a growing group of people around the globe who, like you, are discovering an easier way to mop their floors. The use of practical robots that help you in and around your home is a new reality. We encourage you to share your feedback as we continue to develop new and groundbreaking robots. [. . . ] •  Once Braava has completed its run, you can move the Cube to clean a different part of your home. Using Braava with multiple Cubes (For Braava 380t ONLY): •  Use one or more extra Cubes (sold separately) to expand how far Braava cleans in a single run. * •  Place extra Cubes in rooms or areas next to the area covered by the first Cube. The Cubes should typically be between 20 and 25 feet from each other for the NorthStar coverage to overlap. •  Braava will automatically clean from one Cube to another. C * ubes are pre-programmed to different NorthStar channels, indicated on the bottom of the Cube. Cubes with different channels must be used for multi-Cube cleaning. 25’ One Cube Multiple Cubes global. irobot. com 17 Operating Braava Put On a Cleaning Cloth 1.  Braava on its end and remove the cleaning pad. Set 2.  Attach a dry or wet cloth to the Multi-Purpose cleaning pad. Lay the removable pad on an open cleaning cloth. Attach cloth by tucking it into the gripping strips on both sides. See the following page for the Pro-Clean Reservoir Pad. 3.  Re-attach the cleaning pad. Magnets will help it snap back into place. 1 2 3 CAUTION: Make sure the cleaning cloth does not drape into the middle channel between the gripping strips as this could impede sensor functions and safe operation. 18 Braava 300 Series Owner’s Manual Using the Pro-Clean Reservoir Pad (Sold separately for Braava 320) The Pro-Clean Reservoir Pad dispenses liquid as Braava mops to keep the cleaning cloth wet longer. Fill the reservoir 1.  pen the fill cap by pulling and swiveling it O to the side. 2.  reservoir with water and replace fill cap, Fill pressing it in securely so it does not leak. 3.  ill the reservoir over a sink as a small F amount of fluid can leak out when the fill cap is closed. Dampen the blue Pro-Clean microfiber 4.  cloth and press onto the velcro strips. Do not use a dry cloth. TIP:  luid dispenses at different rates depending on floor type and solution F used. The first time you mop, start with the cloth only slightly damp and then increase the starting cloth wetness if needed. NOTICE: To avoid the Pro-Clean Reservoir Pad leaving excess fluid on your floor, do not leave Braava unattended when mopping and remove from floor once Braava stops cleaning. When mopping is finished: • Empty any remaining fluid from the reservoir. •  Leave the fill cap open to allow reservoir to dry completely. • See page 22 for care instructions. global. irobot. com 19 Place the NorthStar ® Cube 1.  Press the button on the back corner of the NorthStar Navigation Cube to turn it on. A blue light will flash on the opposite corner when turned on, and then go solid when Braava locks onto it. I f you forget to turn the Cube on, Braava  ill send a signal w to try to turn it on. f Braava is I successful, the blue flashing light will appear on the Cube. 2.  lace the NorthStar Navigation P Cube on a table or counter top, pointing the blue light away from walls and toward the middle of the room. For Best Results •  Place the NorthStar Navigation Cube where it has a clear view of the ceiling (for example, no cabinet or shelf directly above it). •  not move the NorthStar Navigation Cube once Braava has started Do cleaning as t may impair Braava’s cleaning performance. i •  not put the NorthStar Navigation Cube on the floor as the cleaner Do may run into it and move it. 20 Braava 300 Series Owner’s Manual Start Cleaning Place Braava on the floor within 6-8 feet of the NorthStar Navigation Cube, facing toward the Cube. [. . . ] Clean wheels with a cloth dampened with warm water to remove dust and cleaning solution. Let the wheels dry before cleaning again. When reapplying, follow these instructions: •  nsure cloth does not overlap into the middle channel of E the removable cleaning pad •  nsure cloth is not bunching up, which can prevent the E removable pad from reattaching completely to the robot. •  heck wheel area for debris and remove or clean as needed. [. . . ]