User manual IROBOT VERRO 300

[. . . ] iRobot® Verro Model 00 ™ OWNER’S MANUAL  Safety Notes WARNING: Your cleaner should not be used while people are swimming in the pool. A Ground Fault Current Interrupter (GFCI) must be installed to protect your electric outlet and prevent any possible electric shock. The unit must be supplied through a Ground Fault Current Interrupter outlet. The connection to the branch circuit should be consistent with the local and national wiring rules (electrical code). [. . . ] 7 8 9 Replace filter bag assembly in the robot. Make sure the tabs click into place. 14 iRobot Verro Owner’s Manual  Maintenance and Adjustment Rinsing Verro iRobot recommends that you rinse Verro with a garden hose after using it. This will extend the life of the plastic and keep your robot looking good for years to come. Storage Store Verro in a dry place out of direct sunlight at a temperature between 50 and 104 degrees Fahrenheit. The Power Supply is water resistant, but not waterproof and may be damaged by rain. Important: Failure to properly store Verro will result in loss of warranty. www. irobot. com 15  Maintenance and Adjustment (cont. . . ) Untwisting the Floating Power Cord Check the floating power cord periodically for external damage. Verro is designed to travel around your pool in a way that reduces any tendency for the cord to become twisted. However, if the cord tangles or kinks, and will not lie properly on the surface of the water, it may be necessary to untwist it using the Detangler. 1 Unplug the Power Supply. (Please keep the plug away from contact with water. ) Unplug the floating power cord from the Power Supply. 2 Place the robot so that you can walk away from it for 50 feet. 3 Holding the Detangler in your hand, walk away from Verro. The Detangler allows the floating power cord to rotate in the handgrip so that it untwists as you walk. 4 If the cord is not fully untwisted by the time it is straight, simply give it a few more turns by hand. 16 iRobot Verro Owner’s Manual  Maintenance and Adjustment (cont. . . ) Cleaning the Impeller Verro uses an impeller to pump water up through the vacuum intakes at the bottom of the robot and out the jet valve housing at the top. If this impeller becomes fouled by hair, string, etc. it will reduce the amount of water Verro can pump and may reduce the life of the motor. If you notice that Verro is not cleaning well or that it is having difficulty moving around the pool, and other measures (cleaning the filter bag, checking the vacuum intakes, etc. ) have not corrected the problem, check the impeller. 1 Unplug the Power Supply. (Please keep the plug away from contact with water. ) Unplug the floating power cord from the Power Supply. It may be helpful to remove the jet valve port (see Cleaning the impeller, above) in order to see the direction baffle. Check to make sure that it swings freely in both directions. 20 iRobot Verro Owner’s Manual  Troubleshooting Most problems with Verro are caused by a dirty or clogged filter bag. Verro depends on water flowing freely through the filter bag to operate at peak efficiency. If the filter bag gets clogged, Verro will not be able to clean as effectively and may not move as well. The fine filter bag can trap particles as small as two microns across and can be clogged by particles too small to see. If rinsing the filter bag by hand with a hose doesn’t solve the problem, try machine-washing it in cold water. Don’t use detergent, fabric softener, bleach, or any other additive. If you find the fine filter bag gets clogged too quickly, consider using the mesh bag instead. Always turn off Verro’s Power Supply and unplug it before troubleshooting any problem. Problem likely Cause Verro moves The filter bag needs to slowly be cleaned Flaps in the vacuum intakes at bottom of robot are blocked Wheels or axles are not turning freely The pump impeller is fouled by dirt or debris The filter bag needs to be cleaned What to Do Clean the filter bag. [. . . ] Tip Periodically straighten the floating power cord with the Detangler. Tip Verro’s Power Supply has an automatic timer that shuts Verro OFF after approximately two hours of operation. When this happens, the power switch will remain ON. To start another cleaning cycle, switch the Power Supply OFF and then back ON and then press the reset button. Turn the Power Supply switch ON then press the reset button. [. . . ]