User manual ISEKI KC 450

[. . . ] Pass them on to possible new owners of the appliance. also be equipped with vents to allow gas to escape in the event of a leak. As a result LPG cylinders, whether partially or completely full, must not be installed or stored in rooms or storage areas that are below ground level (cellars, etc. ). It is advisable to keep only the cylinder being used in the room, positioned so that it is not subject to heat produced by external sources (ovens, fireplaces, stoves, etc. [. . . ] When the installation process is complete, check the pipe fittings for leaks using a soapy solution. Adapting to different types of gas To adapt the hob to a different type of gas other than default type (indicated on the rating plate at the base of the hob or on the packaging), the burner nozzles should be replaced as follows: 1. Remove the hob grids and slide the burners off their seats. Unscrew the nozzles using a 7 mm socket spanner, and replace them with nozzles for the new type of gas (see table 1 “Burner and nozzle characteristics”). Reassemble the parts following the above procedure in the reverse order. Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used. Sticker are available from any of our Service Centres. Replacing the nozzles on separate “double flame “ burners: 1. remove the grids and slide the burners from their housings. The burner consists of 2 separate parts (see figure); 2. unscrew the burers with a 7 mm wrench spanner. When using models with an ignition button, light the desired burner pressing down the corresponding knob as far as possible and turning it anticlockwise towards the maximum setting. If a flame is accidentally extinguished, turn off the control knob and wait for at least 1 minute before trying to relight it. To switch off the burner, turn the knob in a clockwise direction until it stops (when reaches the “•” position). The “separate double flame” burner* This burner consists of two concentric burners which can operate either together or separately. Use of the double flame on the maximum setting gives a very high power which reduces cooking times with respect to conventional burners. • Always use cookware with a flat base and a cover. * Only available on certain models. 7 GB • When the contents of the pan reach boiling point, turn the knob to minimum. Burner Semi-Rapid (S) Auxilliary (A) Triple Crown (TC) Double flame (DCDR internal) Double flame (DCDR external) ø Cookware diameter (cm) 16 - 20 10 - 14 24 - 26 10 -14 26 - 28 To obtain the best results from your hob: • Use flat-bottomed pans to ensure that they adhere to the cooking zone perfectly. • Always use pans with a diameter that is large enough to cover the hotplate fully, in order to use all the available heat. !On the models supplied with a reducer shelf, remember that this should be used only for the Double flame internal (DCDR internal) burner when you use casserole dishes with a diameter under 12 cm. To identify the type of burner, refer to the designs in the section entitled, "Burner and Nozzle Specifications". • Make sure that the bottom of the cookware is always dry and clean to guarantee correct adherence and long life, not only for the cooking zones but also for the cookware itself. • Avoid using the same cookware that is used on gas burners: the heat concentration on gas burners may deform the base of the pan, causing it not to adhere correctly. • Never leave a cooking zone on without cookware on it because as it heats up and rapidly reaches the maximum level, which could damage the heating elements. Practical Advise on Using the Ceramic Glass Module* Set. Off To melt butter and chocolate. * Only available on certain models. 8 Precautions and tips ! [. . . ] After cleaning, rinse and dry any remaining drops of water. • Before using the ceramic glass module, the surface must be cleaned, using a damp cloth to remove dust or food residues. The ceramic glass surface should be cleaned regularly with a soultion of warm water and a nonabrasive detergent. Periodically, special products will need to be used to clean the surface. [. . . ]