User manual ISEKI SA370F

[. . . ] EINACHSSCHLEPPER ISEKI HAKFREZEN EN EENASSIGE TREKKERS MOTOAZADAS ISEKI 1 INTRODUCTION This operator's manual is intended to provide necessary information for operating and maintaining your tiller. Its primary purpose is to offer guidance in the proper and safe operation of your power tiller in dajJy and seasonal work. We especially wish to call your attention INTRODUCTION Ce manuel d'instructions comporte "information necessaire pour la commande et \'entreticn de vos motobineuses et motoculteurs ISEKI et comprend SurtOlit des prescriptions de securite pour Ie travail courant et saisonnier, pour lesquelles nous demandons votre attention particuliere. S'il faut reparer ou remplacer des pieces, servez-vous toujoUJs de pieces originales ISEKI. [. . . ] (1) commande d'enrichissement (2) position fonctionnement (3) position demarrage STOPPING CONTROLS • ENGINE SWITCH Turn the lever to the "STOP" position, and then the engine stops. La puissance de moteur ne sera transmise que lorsque Ie er is transmitted only while the lever is grasped in the "Engageing" position. (1) Desconectar (2) Conectar 29 DRIVING CONTROLS • MAIN SPEED SHIFT LEVER COMMANDES DE CONDUITE • LEVIER DE CHANGEMENT DE VITESSES A ~ O' D V m' 1st and 2nd speed in direction of arrwhead (F) 3rd and 4th speech in direction of arrowhead (F) 1st and 2nd speech in direction of arrowhead (R) A ~ O' m' 1e et 2e vitesse dans la direction de la fleche (avant) 3e at 4e vitesse dans Ja rection de la fleche (avant) di~ D V 1e et2e vitesse dans la direclion de la fleche (arriere) Four forward speeds and two reverse speeds are available with this shift lever in accordance with the shift guide. Warning: When the steering handle bars are turned around fully, also turn around the main speed shift lever. If you do not, you may make a mistake in shifting positions) which may lead to an accident. Marche arriere (3) Levier de changement de position vitesses principal (4) Mancherans en position normale Warning: When the steering handlebars are turned around fully in the opposite position, be sure to reset the location ofthe reverse shift lock plate by laos· ening the wing nuts. If you do 1I0t, the main speed shift lever can be shifted to the reverse high speed positioll, which lIlay lead to an accident. 31 Note: When the handlebars are turned around to the normal position, remember to reset the lock plate to the original position. remarque: Lorsque Les mancherons sont retourlUis en position norma/e , n'oubliez pas de rajuster La pLaque de verrouillage dans sa position originate. €¢ HIGH-LOW SPEED SHIFT LEVER CI ---: ill: • LEVIER DE CHANGEMENT DE VITESSES LENTjRAPIDE Low speed' High speed ---: 'f, I: Petite vitesse Grande vitesse • BELT SHIFTING On the type F power tillers, the highlow speed ranges are produced by shifting the driving belt manually. • PASSE-COURROIE Sur les modeles F des motobineuses et motoculteurs , les differentes pi ages de vitesses sont realisees en passant la courroie d'entrainement a la main. //_~ • STEERING CLUTCH LEVERS (SA560, 570, 580, 360F, 370F) • LEVIERS DIRECTIONNELS (Modeles SA360F, SA370F) The machine turns in the direction in which lever is grasped. 32 - Warning: When the machine is used with the handlebars turned around in the opposite direction, be sure to inter. Change the right and left steering clutch levers. [fyou do not, the machine will turn in the opposite direction against your will, which may lead to an accident. (Die Maschine kann sonst zu 33 OTHER CONTROLS SA560, 570, and 580 • HANDLEBAR ROTATING LEVER The handlebars are free to rotate by grasping the lever. The handlebars rotate only within the range shown in the figure. €¢ HANDLEBAR ANGLE CONTROLKNOB The handlebar angle is adjustable in every lr step with this knob. (1) Handlebar height control knob (2) Handlebar rotating lever • BOUTON D'INCLINAISON DES MANCHERONS Ce bouton permet de regler I'inclinaison des mancherons par echelon de ]20. I (1) Bouton d'inclinaison des mancherons (2) Levier de rotation des mancherons DRIVING CONTROL SA360 and 370 COMMANDE DE CONDUITE Modeles SA360 , 370 • LEVIER DE CHANGEMENT DE VITESSES CD ® ® 110° 110° 20° • MAIN SPEED SHIFT LEVER t t 34 6: II" 1st speed in direction of arrwhead (F) 2nd speech in direction of arrowhead (F) 3rd speech in direction of arrowhead (F) 1st and 2nd speech in direction of arrowhead (R) mil V t t "' t 1ere vitesse avant 2eme vitesse avant 3eme vitesse avant 1ere vitesse arriere derjelVeiligen Richtang abrappt uusbrechen. Dad direccion flecha, (Atras) 35 Three forward speeds and two reverse speeds are available with this shift lever in accordance with the shift guide. le levier de vitcsses permet de selectionner 3 vitesses avant ct 1 vitesse arriere en fonctionnement normal , et 1 vitesse avant lente et 1 vitesse arriere lente cn fonctionncment inverse. [. . . ] It has dried well, soak it in engine oil and squeeze oil well out of it. Pat the paper element softiy to dust off or blow it from inside with pressurized air. Or wash it in water with detergent and then well in fresh water. Wipe off dust or dirt from the cases and then assemble the air-cleaner. [. . . ]