User manual JABRA EHS BROCHURE

[. . . ] ElEctronic Hook SwitcH (EHS) SolutionS Jabra® is a registered trademark of gN Netcom a/s www. Jabra. com electronic Hook switch (eHs) solutions DiScovEr frEEDom witH Jabra Why Jabra hEadSEtS? Jabra headsets are more ergonomic and convenient to use, enhancing flexibility and the ability to multitask with maximum efficiency. Once you discover the benefits of hands-free telephony, you never want to go back to traditional handsets. Freedom for all Jabra headsets allow you to search for documents, make copies or enter data on your PC while talking to a customer. With a wireless headset you can enjoy freedom of movement up to 150 meters away from your desk. [. . . ] Set compatibility selector (Telephone Termination Switch Wheel) in position "A" 2. Set the base unit to the DHSG mode by keeping the headset in the base and hold the volume +/- buttons on the headset for 6 seconds until the red light on the base flashes rapidly. Scroll through the four different settings using +/- and set to the lips icon. Leave for 15 seconds until the unit has displayed the confirmation flash sequence and it is ready to go! ­ + Volume button Jabra LiNkTM 14201-19 eHs adapter for avaya Jabra LiNkTM 14201-20 eHs adapter for avaya or or or Jabra ProTM 9400 series Jabra goTM 6470 Jabra gN9350e/ Jabra gN9330e eHs Jabra gN9120/ Jabra gN9125 eHs Setting up Jabra GN9330e EhS 1. Push simultaneously 5 sec on the 2 buttons (base station and headset ­ see illustrations next column) 3. LED on headset starts to blink rapidly 4. Choose EHS mode with volume control on headset. LEDs on base indicates selected mode: LED 2: DHSG mode 5. Push simultaneously 5 sec on the 2 buttons (base station and headset ­ see illustrations next column) 3. LED on headset starts to blink rapidly 4. Choose EHS mode with volume control on headset. LEDs on base indicates selected mode: LED 2: DHSG mode 5. When LED on headset stops blinking, start using headset. regional sales contacts: Americas: Bill Orlansky, borlansky@gn. com EMEA: Norbert Lohwieser, nlohwieser@gn. com APAC: Mike Powrie, mpowrie@gn. com Setting up Jabra GN9120/GN9125 EhS 1. Set compatibility selector (Telephone Termination Switch Wheel) in position "A" 2. Set the base unit to the DHSG mode by keeping the headset in the base and hold the volume +/- buttons on the headset for 6 seconds until the red light on the base flashes rapidly. Scroll through the four different settings using +/- and set to the lips icon. Leave for 15 seconds until the unit has displayed the confirmation flash sequence and it is ready to go! ­ + Volume button MSH RHL DHSG AEI Visual indicator (red) Link icon Mute icon Charge icon For more information and disclaimer, visit www. jabra. com/cisco 7 electronic Hook switch (eHs) solutions for Nortel SuPPOrtEd NOrtEl IP PhONES SEt uP INFOrmatION To connect your Nortel phone and Jabra headset, just follow these simple steps: Nortel iP phone 1120e Nortel iP phone 1140e Nortel iP phone 1150e Setting up the Nortel phone 1. In the "Preferences" menu, choose "Headsets. . . " 2. In "Active Headset Device" select the appropriate headset type from a list of Wired, USB, or Bluetooth headsets. Selection of a particular headset type fine tunes the audio to that particular headsets type. Selecting the right headset type is therefore recommended to achieve best performance. [. . . ] With the cable marked red, connect the AUX socket on your headset base unit to the Jabra LINK EHS Adapter AUX socket. Note: The marked end of each cable must be connected to the Jabra LINK EHS adapter. Note: When using the EHS adapter with Avaya phones, please note that the MFB button on your headset acts as the Master button for on- and off-hooking your telephone. This means that both devices can work independently, but the MFB may override the headset button on the telephone. [. . . ]