User manual JACUZZI LT5SK REMOVABLE SKIRT INSTALLATION INSTRUCTIONS

[. . . ] Jacuzzi Premium constantly strives to offer the finest spas available, therefore modifications and enhancements may be made which affect the specifications, illustrations and/or instructions contained herein. This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and uses radio frequency energy. [. . . ] N. B. : Never allow anyone to stand or sit on the cover. 2. 3. 4. 5. 2. Locate the drain valve on the front/lower panel. Hold the larger (rear) body to prevent it from turning, then loosen and remove the cap. Attach the hose. 57 Panel maintenance The panels do not require any special maintenance. To clean them, just wipe them with a clean cloth soaked in a soultion of water and a neutral detergent. ATTENTION: do not direct jets of water against against the, since electro-mechanical parts of the spa are located behind them. - Replace the drain plugs and screw them on. - Loosen the clamp on the bottom of the heater and remove the hose. After draining the water, re-insert it on the connection and tighten the clamp again. - Re-install cabinet panels and cover spa with the insulating cover. Restarting your spa in cold weather Winterizing I Your Jacuzzi ® Premium spa is designed to automatically pro- tect itself against freezing when operating properly. I During periods of severe freezing temperatures, you should check periodically to be certain that the electrical supply to the spa has not been interrupted. I Under very cold conditions check that the filtration cycle is pro- If you want to start up your spa after it has sat empty for a time in freezing temperatures, check whether the water remaining in certain sections of the piping is still frozen: this situation may block water flow preventing the spa from operating properly and possibly damaging the equipment. Under these circumstances we recommend contacting your reseller prior to attempting to restart the spa. grammed for 24 hours ("Primary filtration cycle" chapter) and that the automatic heating mode is active ("Water recycling" - "Automatic cycle" chapters). I During the periods of non-use and/or prolonged interruption Water quality maintenance Maintaining the quality of the water within specified limits will serve to enhance your enjoyment and prolong the life of the system. It is a fairly simple task, but it requires regular attention because the water chemistry involved is a balance of several factors. A careless attitude in regard to water maintenance will result in poor and potentially unhealthful conditions for soaking and may even damage your spa. - If the condition persists, contact your retailer. "WATER IS BELOW SET-TEMP" If the spa water temperature is 6°C lower than the set temperature the recirculation pump and heater are automatically activated to guarantee the anti-freezing protection. The spa remains in this mode until the water temperature is 9°C lower than the set temperature. "COMMUNICATION ERROR" The communication between the control panel and the electric box is defective. I Contact your dealer or service center. "PUMP DOES NOT OPERATE" Heater is deactivated; recirculation pump may also be deactivate. Proper flow of water is obstructed or a flow switch has malfunctioned. Check for proper water level and for a clogged filter cartridge. I If there is not a noise (relative to the possible functioning of "SHORTED SENSOR" The maximum temperature sensor does not work (the heater is deactivated). I Contact your reseller or an authorised assistance centre. "START-UP MALFUNCTION" CLOSE D OR SHORTE D FLOW SWITCH ON SYSTE M STARTUP (system disabled) Flow switch is non-functional. I Contact your reseller or an authorised assistance centre. Temperature symbol is flashing Indicates that: I There is a difference of approximately 6 °C between the real temperature and the set temperature or I The temperature sensor has read a value exceeding 44 °C, or I The maximum temperature sensor has read a value exceeding the electro-mechanical parts) or if there is a continuous hum, disconnect the spa (the pump could be incorrectly primed; refer to the "The pump does not operate" chapter). I Contact your dealer or service center. 46 °C. "FREEZE PROTECTION" A potential freeze condition has been detected. Pump(s) operate until the spa is out of danger. It is possible to turn off the pumps via the control panel. However, if after 2 hours freezing conditions persist, the pumps will restart automatically. "Please check filter" (check the filter cartridge) 6:45 PM 102F Please check filter! T emp. 59 This message appears when the reminder for the change or cleaning of the filtering cartridges expires. I Clean or replace the filter cartridge (see also relative chapter). Troubleshooting If the spa does not operate correctly review all of the installation and operating instructions in the present manual and control the message shown on the display. [. . . ] Fogged optical components inside the unit will return to normal operation after an hour in a heated environment. 66 J-1000 REMOTE CONTROL Most parts of the functions can be managed through this remote control whose main characteristics are: - when turning on, the remote control will check the correct communication with the spa control unit; a control procedure that individuates the various active functions (that are indicated on the remote control display itself) will start. The water temperature and the main menu are also shown. - if the remote control remains unused for a period of approximately 15 seconds it will be turned off automatically; press any button to reactivate the remote control (the display and the keypad will light up). Note: the remote control is water resistant (but not water tight); store in a dry place when not in use . [. . . ]