User manual JATON VIDEO-PX6200TC-128LP

[. . . ] Video-PX6200TC series nVIDIA GeForceTM 6200 series User's Manual Version 3. 00 Copyright © 2006 Jaton Corporation, USA Contents INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FEATURES AND SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SYSTEM REQUIREMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 CHECK LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To maximize the video board acceleration and increase its performance, you may install the manufacturer's display driver as follows: 14 1. Autorun feature brings-up the "Welcome Screen", and you may point to "Display Driver" and then press on it. 2. Microsoft InstallShield® Wizard has start loading its setup process; please wait until it has completed. 15 3. Click on "Next" to continue the process. 4. The Windows system will copy all driver files from source media to your local hard disk; please wait until the process has completed. 16 5. Click on "Finish" to restart your computer, the new display driver will be in place after Windows boots-up. Windows® 2000 Driver Installation InstallShield® Program: Microsoft Windows®2000 detects this new hardware and places appropriate display driver from its system folder automatically - it doesn't matter if you have added a new driver or changed the existing one. To maximize the video board acceleration and increase its performance, you may install the manufacturer's display driver as follows: 17 1. Autorun feature brings-up the "Welcome Screen", and you may point to "Display Driver" and then press on it. 2. Microsoft InstallShield® Wizard has start loading its setup process; please wait until it has completed. 18 3. Click on "Next" to continue the process. 19 4. Click on "Finish" to restart your computer, the new display driver will be in place after Windows boots-up. Notice: We believe that the all the installation steps mentioned above are clear from manufacturer software's CD to your operating system. Any procedures other than these processes have not been specified. Technical Assistance Q: Why is the display shifted or changed sizes when I switch display modes?Explain and Suggestion: Some monitors lack auto-sizing features or just do not synchronize properly to the video board output. In some cases, horizontal and vertical display adjustments may be necessary. Use the monitor control panel functions to adjust screen. In other cases, mode type and refresh rate adjustments may be necessary. Use the utility program, which provided by video card manufacturer or production developer. To center the display with normal type (mode 3), and to reduce (decrease) the refresh rate with the monitor's specification. Q: What kind monitors can display 800x600 modes or higher resolution mode?Explain and Suggestion: To display 800x600 resolution at 60Hz refresh rate, the monitor must be capable of synchronizing a 31. 5KHz horizontal scan rate (e. g. , NEC 2A, 3D). At 72Hz refresh rate, the monitor must be capable of synchronizing a 48. 0KHz scan rate (e. g. , Sony HG 1304, NEC 4D, 5D, Seiko 1450). To display 1024x768 interlaced mode; the monitor must be capable of synchronizing a 35. 5KHz horizontal scan rate (e. g. , NEC 3D, Seiko 1430 or 1440). To display 1024x768 non-interlaced mode at 60Hz, the monitor must be capable of synchronizing a 48. 7KHz scan rate (e. g. , Sony HG 1304, NEC 4D, 5D, Seiko 1450). [. . . ] All Trademarks and Registered Trademarks belong to respective owners. ©2006 Jaton Corporation. All rights reserved. Other Limits The forgoing is in lieu of all other warranties, expressed or implied. Including but not limited to the implied warranties of merchantability and fitness for a particular purpose. Manufacturer does not warrant against damages or defects arising out of improper or abnormal use of handling of the products; against defects or damages arising from improper installation (where installation is by persons other than Manufacturer), against defects in products or components not manufactured or installed by Manufacturer, or against damages result from non-manufacturer made products or components. [. . . ]