User manual JATON VIDEO-PX7300GS-256

[. . . ] Video-PX7300 series nVIDIA GeForceTM 7300 series User's Manual Version 1. 00 Copyright © 2006 Jaton Corporation, USA Contents INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FEATURES AND SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SYSTEM REQUIREMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 CHECK LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Slide the slot cover out and put the screw aside (you will need it to secure the adapter). To install the adapter in AGP expansion slot, carefully line up the goldfingered edge connector on the adapter directly above the expansion slot connector on the motherboard. Then press the adapter into place, completely. Use the (remaining) screw you removed to secure the adapter-retaining bracket in place. Secure the cover with the mounting screws you removed in Step 3. 4. 5. 6. You have now completed the installation of your new graphics adapter on your system. Upgrade Steps: Add or change your video adapter to an existing system, you may precede a few steps before you install the new hardware and software (video display driver). The followings are some of the considerations: 10 1. To add a new adapter, ensure the mainboard has available IRQ for new devices, and there is no conflict between each other. If you try adding this video adapter to an ALL-IN-ONE mainboard (which video port built-in already), then you have to disable that port first. Otherwise, that will be a problem for the new video adapter setup. The driver installation for system upgrade is the same as below, if error occurs when you proceed to step 1, 2 or 3, please consult with your system dealer or the existing hardware manufacturer support. Software Installation Windows® XP/2000 Driver Installation InstallShield® Program: Microsoft Windows® XP/2000 detects this new hardware and places appropriate display driver from its system folder automatically - it doesn't matter if you have added a new driver or changed the existing one. To maximize the video board acceleration and increase its performance, you may install the manufacturer's display driver as follows: 11 1. Autorun feature brings-up the "Welcome Screen", and you may point to "Display Driver" and then press on it. 2. Microsoft InstallShield® Wizard has start loading its setup process; please wait until it has completed. 12 3. Click on "Next" to continue the process. 4. The Windows system will copy all driver files from source media to your local hard disk; please wait until the process has completed. 13 5. Click on "Finish" to restart your computer, the new display driver will be in place after Windows boots-up. Notice: We believe that the all the installation steps mentioned above are clear from manufacturer software's CD to your operating system. Most AGP video cards designed for Plug-n-Play, that means video card IRQ's setup which controls by main board's (motherboard) circuitry and BIOS. Physically pulling out other devices from system, and re-starts the computer. Confirm and modify your IRQ addresses with qualified computer technician. Q: Multiple images or unreadable screen after loading video driver. Explain and Suggestion: There are a variety of reasons why the display might be distorted. One common reason is a monitor mis-match. Some older multi-frequency monitors are unable to switch video modes without being turned off, then turned on again. [. . . ] All Trademarks and Registered Trademarks belong to respective owners. ©2006 Jaton Corporation. All rights reserved. Other Limits The forgoing is in lieu of all other warranties, expressed or implied. Including but not limited to the implied warranties of merchantability and fitness for a particular purpose. Manufacturer does not warrant against damages or defects arising out of improper or abnormal use of handling of the 22 products; against defects or damages arising from improper installation (where installation is by persons other than Manufacturer), against defects in products or components not manufactured or installed by Manufacturer, or against damages result from non-manufacturer made products or components. [. . . ]