User manual JBL 1400 ARRAY

[. . . ] 1000 800 1400 1000 Project Arrray 800 1400 1000 800 880 Project Arrray 1400 Project Arrray Project Arrray 1 Project Arrray Project Arrray Project Arrray Project Arrray Project Arrray Project Arrray 1500 Project Arrray 880 1400 880 1400 Project Arrray Project Arrray Project Arrray 1500 Project Arrray 1500 Project Arrray Project Arrray ® JBL PROJECT ARRAYTM 1500 ARRAY, 1400 ARRAY, 1000 ARRAY, 880 ARRAY, 800 ARRAY OWNER'S GUIDE READ FIRST!Important Safety Precautions! CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: To reduce the risk of electric shock, do not remove cover (or back). Refer servicing to qualified service personnel. CAUTION: To prevent electric shock, do not use this (polarized) plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] Notice the two threaded inserts on the angled face of the top and also the small L-bracket on the top. These are the attachment points for the horn module. Immediately adjacent to the Lbracket is a recessed connector which will make the electrical connection for the horn module. Although the module can be installed by one person, it is easier if a second set of hands are available. Cradle the horn module with the opening along your forearm and, using your free hand, connect the plug coming from the bottom of the horn assembly into the jack on the top of the enclosure. You can now place the horn in position on top of the enclosure. The L-bracket fits in an opening under the horn assembly. The module will sit on top of the enclosure by itself, although it should always be steadied until fully mounted. Line up the two mounting holes on the lower lip of the front of the horn with those in the enclosure. Partially install one long bolt and then the other one. It may be necessary to lift the horn slightly so that the bolts install smoothly. Once both bolts have been started, work them in all of the way, but do not tighten them securely just yet. Install the remaining short bolt in the hole at the bottom rear of the horn module. Now completely tighten the two front bolts. Everything should be tight and properly aligned at this time. If not, loosen, realign, and retighten as required. The final steps are to remove the backing from the logo badge and place it in the recess on the lower horn lip, and to use the rubber hole plug to hide the hole at the bottom rear of the horn module. Do not complete these steps until the system has been turned on and tested acoustically. Make sure the horn module is playing first. Once the logo badge and rubber plug hole are installed, it is extremely difficult to remove them. 6 Step 9 Step 7 Step 11 Step 8 7 SPEAKER CONNECTIONS Subwoofer Controls and Connections (15 0 0 Array Only) ¡ Line-Level Input 2 3 0 1 4 5 6 7 TM Line-Level Output £ Power Indicator ¢ Subwoofer Level (Volume) Control Crossover Adjustment § Phase Switch ¶ LP/LFE Selector · On/Off Auto Switch ª Power Switch Connection: If you have a Dolby® Digital or DTS® receiver/processor with a low-frequencyeffects (LFE) output, set LFE/LP switch to LFE. Many users have a tendency to set the subwoofer volume too loud, adhering to the belief that a subwoofer is there to produce lots of bass. A subwoofer is there to enhance bass, extending the response of the entire system so the bass can be felt as well as heard. [. . . ] · Review proper operation of your receiver/amplifier. If there is no sound coming from one speaker: mode. If it is not, check to see whether your receiver/amplifier has other surround modes you may use. · In Dolby Digital or DTS modes, make sure your receiver/ processor is configured so that the surround speakers are enabled. · Review the operation of your DVD player and the jacket of your DVD to make sure that the DVD features the desired Dolby Digital or DTS mode, and that you have properly selected that mode using both the DVD player's menu and the DVD disc's menu. · Check all wires and connections between receiver/ amplifier and speakers. [. . . ]