User manual JBL AS SUB

[. . . ] Please take a moment to complete the enclosed profile card. It enables us to keep you posted on our latest advancements, and helps us to better understand our customers and build products that meet your needs and expectations. [. . . ] However, if you are unsure of your ability to properly install these loudspeakers, please contact your dealer or a qualified installer. Tools Needed Phillips #2 screwdriver Measuring tape Utility knife Pencil Carpenter's level Awl AS5, AS6, AS8 Installation Kit Template Speaker frame Thread-forming screws Retainer clips Four mounting brackets Short phillips head screws AS Series Owner's Manual 9/11/98 12:51 PM Page 5 Existing Construction Level 1-1/2" 1-1/2" 1-1/2" Template Tape Step One: Remove the grille from the speaker frame. Step Two: Determine the correct speaker location. Step Three: Determine the speaker-frame location. Kerf Line Step Four: Cut the dry wall. Step Five: Place the mounting bracket on the speaker frame using the mounting guides (marked 3/8" , 1/2" 5/8" and 3/4") corre, , sponding to the thickness of the dry wall. Step Six: Place the frame assembly in the wall. Step Seven: Connect the speaker wires to the baffle assembly and install baffle assembly in frame. Do not overtighten the baffle screws. Step Eight: Replace the metal grille. AS Series Owner's Manual 9/11/98 12:51 PM Page 6 New Construction 1-1/2" 1-1/2" 1-1/2" Step One: Remove the grille from the speaker frame. Step Two: Determine the correct speaker location. Step Three: Attach the proper mounting brackets, marked and preset at 3/8" 1/2" 5/8" and 3/4" corre, , , , sponding to the thickness of the dry wall, to the speaker frame. Step Four: Nail or screw the speaker-frame assembly to the wall studs and route the wires through the frame opening. After the Drywall is Installed Step Five: Cut the drywall. Step Six: Connect the speaker wires to the baffle assembly and install baffle assembly in frame. Do not overtighten the baffle screws. Step Seven: Replace the metal grille. AS Series Owner's Manual 9/11/98 12:51 PM Page 7 AS SUB 1-1/2" 1-1/2" 1-1/2" Step One: Remove the grille from the subwoofer frame. Step Two: Determine the correct subwoofer location. Step Three: Cut the drywall. Step Four: Loosen the eight phillips head screws until the locking tabs turn inward. Step Five: Connect the speaker wires to the baffle assembly. Step Six: Place the subwoofer in the wall. Step Seven: Screw down each of the eight phillips head screws. The tabs will swivel into place and secure the unit to the rear surface of the drywall. Step Eight: Replace the metal grille. AS Series Owner's Manual 9/11/98 12:51 PM Page 8 AS65C 1-1/2" 1-1/2" 1-1/2" Step One: Remove the grille from the speaker frame. Step Two: Determine the correct speaker location. Step Three: Cut the drywall. Step Four: Connect the speaker wires to the speaker. Step Five: Loosen the three phillips head screws on the frame until the locking tabs turn inward. Step Six: Place the frame assembly in the wall. Step Seven: Screw down each of the three phillips head screws. The tabs will swivel into place and secure the unit to the rear surface of the drywall. Step Eight: Replace the metal grille. AS Series Owner's Manual 9/11/98 12:51 PM Page 9 Painting the Speaker Frame and Grille AS Series loudspeakers can be painted to match any style of decor. If you wish to change their color, the satin finish on the grille and frame will function as a primer coat. Before painting, install the paint guard (in the assembly kit) securely into the recess in the baffle. This will protect the speaker components and baffle from paint residue. Use a high-quality spray paint, and apply a thin coat of color. Be certain the grille perforations remain free of paint. Filling them with paint will diminish the sound quality. Note: Gently remove the acoustical foam blanket from the grille before painting. [. . . ] · If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/amplifier. AS Series Owner's Manual 9/11/98 12:51 PM Page 11 Specifications SYSTEM Frequency Response (­6dB): Recommended Maximum Amplifier Power*: Sensitivity: Impedance: Crossover Frequency: Woofer: Tweeter: Outside Dimensions (HxWxD**): AS5 50Hz ­ 20kHz 40 watts 88dB 8 ohms nominal 6kHz 5-1/4" 1" titanium 11 x 7-1/2 x 2-5/8" 280 x 190 x 67mm AS6 40Hz ­ 20kHz 50 watts 90dB 8 ohms nominal 5kHz 6-1/2" 1" titanium 13 x 7-1/2 x 2-3/4" 330 x 190 x 70mm AS65C 45Hz ­ 20kHz 50 watts 90dB 8 ohms nominal 7kHz 6-1/2" 1" titanium 8-1/8 (dia. ) x 2-3/4" 206 (dia. ) x 70mm SYSTEM Frequency Response (­6dB): Recommended Maximum Amplifier Power*: Sensitivity: Impedance: Crossover Frequency: Woofer: Tweeter: Outside Dimensions (HxWxD**): AS8 35Hz ­ 20kHz 60 watts 88dB 8 ohms nominal 5kHz 8" 1" titanium 15-1/8 x 11 x 3-1/4" 385 x 280 x 83mm AS SUB 32Hz ­ 300Hz 120 watts 88dB 8 ohms nominal 300Hz 8" N/A 11-13/16 x 11-13/16 x 3-1/4" 300 x 300 x 83mm Occasional refinements may be made to existing products without notice, but will always meet or exceed original specifications unless otherwise stated. *The maximum recommended amplifier power rating will ensure proper system headroom to allow for occasional peaks. We do not recommend sustained operation at these maximum power levels. ** Mounting depth. AS Series Owner's Manual 9/11/98 12:51 PM Page 12 Declaration of Conformity We, JBL Europe A/S Kongevejen 194B DK-3460 Birkerød DENMARK declare in own responsibility, that the loudspeakers described in this owner's manual are in compliance JBL Consumer Products 80 Crossways Park West, Woodbury, NY 11797 8500 Balboa Boulevard, Northridge, CA 91329 1-800-336-4JBL (4525) (USA only) www. jbl. com 1996 JBL, Incorporated. [. . . ]