User manual JBL BASSQ

[. . . ] JBL® PERFORMANCETM SERIES OWNER'S GUIDE JBL BASSQ TM AUTOMATIC ROOM-MODECORRECTION PROCESSOR ® JBL BASSQTM AUTOMATIC ROOM-MODE-CORRECTION PROCESSOR 3 4 4 5 8 9 10 11 12 Important Safety Instructions Introduction and Features Included Accessories Operation and Controls Connecting Your JBL Performance Series System Installing the JBL BassQ Processor Calibration and Room Mode Correction Troubleshooting JBL BassQ Specifications IMPORTANT SAFETY INSTRUCTIONS 1. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or groundingtype plug. [. . . ] · 8S sends the 12-volt signal 8 seconds after the input signal is received. Movie Trigger Input Using a 12-volt trigger from the Movie/ Music switching can be automated. If you are using the AV1 processor, use the DIN-to-mini trigger cable included with the AV1, as this switching is already programmed into the trigger outputs of the AV1. If you are using the AV2 or another component that has a programmable trigger, use the 2. 5mm to 3. 5mm cable included with the JBL BassQ unit. The remote control will overide the trigger input. Subwoofer Inputs There are two subwoofer inputs. If using an AV1 processor or other processor that has a single subwoofer or LFE output, connect the subwoofer output to the Left input and set the input mode to Mono on the front panel of the JBL BassQ unit. Do not connect the input to the Right input jack, as no signal will be processed. If you are using a preamp/processor such as the AV2, or an AVR that has stereo subwoofer outputs, connect the left and right inputs and set the mode to Stereo on the front panel of the JBL BassQ unit. 16. Subwoofer Outputs There are four subwoofer outputs. These correspond to two subwoofers per side. For best performance, it is recommended that you use at least two subwoofers placed in the front left and front right corners of the room. These would use the L1 (Left 1) and R1 (Right 1) outputs. WARNING: · DO NOT EXPOSE BATTERIES TO EXCESSIVE HEAT SUCH AS DIRECT SUNLIGHT, FIRE OR THE LIKE. · DISPOSE OF DEAD BATTERIES IN ACCORDANCE WITH LOCAL REGULATIONS. 7 CONNECTING YOUR JBL PERFORMANCE SERIES SYSTEM GENERAL INFORMATION A JBL Performance Series system installation incorporates one preamp/ processor (AV1 or AV2), one power amplifier (AVA7) ­ in addition to the amplifier(s) used to power one or more subwoofers ­ and one JBL BassQ processor. If your speaker complement includes the Performance Series PS1400 powered subwoofer (or other powered subwoofer), you may use the amplifier included in each subwoofer. If you are using a passive subwoofer, you will need to supply a subwoofer amplifier. All seven channels on the AVA7 are to be used for driving the left, center and right, and both side and both rear speakers. Use the simplified wiring diagram below, which illustrates how to connect the JBL BassQ unit to a Performance Series system. This diagram is intended to show the signal flow through the system. WIRING DIAGRAM SUGGESTED RACK-MOUNTING ORDER Top 1 AV2 JBL 2 JBL BassQ 3 AVA7 AV2 8-CHANNEL DIRECT IN S/PDIF AUDIO INPUTS COMPOSITE & S-VIDEO INPUTS OUT COMPONENT VIDEO INPUTS HDMI OUT INPUTS OUT POWER MODEL: AV2 JBL, Inc. ANALOG AUDIO INPUTS ANALOG AUDIO OUTPUTS TRIGGERS JBL BassQ AVA7 PS1400 #1 (or other powered subwoofer) Subwoofer LFE Input PS1400 #2 Subwoofer LFE Input 8 INSTALLING THE JBL BASSQ PROCESSOR PHYSICAL INSTALLATION Installation of the JBL BassQ unit is a straightforward process. IMPORTANT: The JBL BassQ unit must be installed following the directions below. [. . . ] Step Six: Enjoy the Music You can now disconnect all the microphones and pack up the stands. Keep these, in case you need to rerun the test. Unmute the preamp and enjoy. Subwoofer Left Front Channel Center Channel Right Front Channel Left Surround Channel 3 1 Couch 2 4 Right Surround Channel 10 Left Rear Surround Channel Right Rear Surround Channel TROUBLESHOOTING Problem: The JBL BassQ unit does not turn on. Neither the red nor blue indicator lights are on. Make sure the JBL BassQ processor is plugged in, and verify that there is the proper voltage at the wall outlet. [. . . ]