User manual JBL CINEMA PROPACK 600

[. . . ] TECHNICAL SPECIFICATIONS Cinema ProPack 600 System General Power Requirement: Contents: Carton Dimensions: AC 120V 60Hz DCR600, DVD600, Programmable Master Remote Control, SCS135S speaker system, basic hookup wiring Width: 37 inches (940mm) Height: 18 inches (457mm) Depth: 23 inches (584mm) 95 lbs. (43. 2kg) Shipping Weight: All features and specifications are subject to change without notice. OWNER'S GUIDE MODEL NUMBER: C I N E M A P R O PA C K 6 0 0 Includes: DCR600, DVD600 AND SCS135S TM PRO SOUND COMES HOMETM JBL Consumer Products 250 Crossways Park Drive, Woodbury, NY 11797 8500 Balboa Boulevard, Northridge, CA 91329 800-336-4JBL (4525) (USA only) D E S I G N G O A L : Re-create the excitement of the movies using high-performance separate components in one convenient package. A U D I O / V I D E O R E C E I V E R : DCR600 with Dolby* Digital, DTS , Logic 7 , VMAx and MP3 Decoding ® ® ® www. jbl. com ©2001 JBL, Incorporated. JBL is a registered trademark of JBL, Incorporated. [. . . ] The words S DELAY TIME appear in the Main Information Display W. Press the / / ¤ Buttons y on the remote once, so that C DELAY TIME appears in the Main Information Display W or in the on-screen display. Press the / / ¤ Buttons y on the remote or the Selector Buttons 5 on the front panel until the desired delay time for the center channel appears in the display. Ô to enter the 13. Press the Set Button setting into the DCR600's memory. 41 REMOTE CONTROL FUNCTIONS The JBL Cinema ProPack 600 is equipped with a powerful remote control that will control the functions of not only the DCR600 receiver and DVD600 DVD changer, but also most popular brands of audio and video equipment, including CD players, cassette decks, TV sets, cable boxes, VCRs, satellite receivers and other home-theater equipment. Once the remote is programmed with the codes for the products you own, it is possible to eliminate most other remotes and replace them with the convenience of a single, universal remote control. red light will flash three times before going dark to confirm the entry. If the device to be programmed in does NOT turn off, continue to enter three-digit code numbers until the equipment turns off. At this point, the correct code has been entered. Press the Input Selector i­n again and note that the red light under the Input Selector will flash three times before going dark to confirm the entry. Try all of the functions on the remote to make certain that the product operates properly. Keep in mind that many manufacturers use a number of different combinations of codes, so it is a good idea to make certain that not only the power control, but the volume, channel and transport controls work as they should. If all functions do not work properly, you may need to use a different remote code. If a code cannot be entered to turn the unit off, if the code for your product does not appear in the tables in this manual, or if not all functions operate properly, try programming the remote with the Auto Search Method. Try all of the functions on the remote to make certain that the product operates. Keep in mind that many manufacturers use a number of different combinations of codes, and it is a good idea to make certain that not only the power control works, but also that the volume, channel and transport controls operate, as appropriate. If all functions do not work properly, you may need to Auto-Search for a different code, or enter a code via the Direct Code Entry method. Programming the Remote As shipped from the factory, the remote is fully programmed for all DCR600, DVD600 and JBL BassQTM digital bass correction functions. In addition, by following one of the methods below, you may program the remote to operate a wide range of devices from other manufacturers. We suggest that you refrain from reprogramming the main, DVD and VID 4 functions. Should you reprogram them inadvertently, you may reprogram each of these buttons individually to code 001 to reset it without disturbing other functions programmed into the remote. Reading Back the Programmed Code When the code has been entered using the Auto Search method, it is always a good idea to find out the exact code so that it may be easily reentered if necessary. You may also read the codes to verify which device has been programmed to a specific Control Selector button. Press and hold both the Input Selector i­n for the device for which you wish to find the code and the Mute Button c at the same time. Note that the Program Indicator will light. [. . . ] · Make certain front panel sensor is visible to remote or connect remote sensor. · Move unit or antenna away from computers, fluorescent lights, motors or other electrical appliances. · Check that Digital Input is selected. Unit does not respond to remote commands · Weak batteries in remote · Wrong device selected · Remote sensor is obscured Intermittent buzzing in tuner · Local interference Letters flash in the channel indicator display and digital audio stops · Digital audio feed paused 67 Troubleshooting (Continued) Disc does not play · Disc loaded improperly · Incorrect disc type · Invalid Region Code · Rating is above parental preset No picture · Intermittent connections · Wrong Input · MPEG-2 decoding · Load disc label-side up. · Check to see that disc is CD, CD-RW, DVD-Movie or Video CD; other types will not play. [. . . ]