User manual JBL CINEMA VISION SYSTEM QUICK START GUIDE_E

[. . . ] Third ­ Last step is to connect JBL Digital LinkTM cable from CVR700 output to port on underside of CVPD50. Do not connect this output port to any device other than the JBL Cinema Vision CVPD50 screen. You have now completed a basic installation of the JBL Cinema Vision System. After a few configuration adjustments, described in Steps 7 through 11 on the inside spread, you'll be ready to enjoy the finest in home theater entertainment! [. . . ] When the on-screen menus are activated while the DVI/Computer source input is in use, the picture will be of the last source used before DVI/Computer if that source had an S-video connection to the CVR700. If the last source did not have an S-video connection, the picture will be temporarily deactivated. The picture-in-picture (PIP) video connection (indicated by a black dotted line) must be composite, and is in addition to any video connection to the main source input jacks. This step is only required if you have external source devices, including a device used for watching television, such as an HDTV tuner, a cable television box, a satellite receiver or a personal video recorder (PVR). Connect your source devices to the CVR700 as shown in Figure 4. All jacks are permanently assigned to the input sources for which they are named. Therefore, although you may connect any audio or video device to any source, always make all connections from a single device to jacks named for the same source. JBL recommends connecting certain device types to certain sources in order to benefit from the preprogramming of the two remote controls: INPUT SOURCE DEVICE TYPES AUX (TV, HDTV Tuner, VCR/Combo, DVD, CD, Cable, Sat) VCR (VCR/Combo) CBL/SAT (Cable, Sat, HDTV Tuner) GAME/CAM (Game, Camcorder) DR (DVD-R, CD-R, DVHS, TiVo®, PVR) DVI/COMP (DVI/DVD, DVI/Cable, DVI/Sat, HD Tuner) AUDIO connections: Right channel (red) on source to right (red) on CVR700, and left channel (white) on source to left (white) on CVR700. DIGITAL AUDIO connections (if available): Choose either coaxial (orange) to coaxial (orange) OR optical to optical for each device. VIDEO connections: Choose component (Y/Pb/Pr ­ green/blue/red), composite (yellow) or S-video (4-pin) for each video source. When using component video inputs, the S-video connection for that source is also required in order to view on-screen menus. When the on-screen menus are activated while the DVI/Computer source input is in use, the picture will be temporarily deactivated. Only the digital video interface (DVI) connection or an analog VGA connection using the supplied cable is available for the DVI/Computer source. When using PIP, composite (yellow) must be used for PIP jack. When source is DVI/Comp, PIP is only available as an inset, not split screen. PIP is not available at all when source is HD component video (480p and better). When you are not using the CVPD50 screen, or if you desire a second display, connect the component, composite and S-video Monitor outputs (if used by your sources) to your video-display monitor or TV. Switch the display's input to match the type of video used for the current source. See Step 6 on back cover of this guide for final connection sequence. Select digital audio and video inputs for external sources: For external sources using the analog audio and composite video inputs with 4:3 aspect ratio (e. g. , VCR), you may skip this step. Press the source selector, then the System selector, then the OSD button to view the main audio menu. Scroll to Sources and press the Set button to view the Sources menu. [. . . ] Following the instructions in the remote's LCD display, scroll until the display shows the number of speakers in your system and press the Set button to select it. Hold the remote steady until the word COMPLETE flashes in the LCD display. (You may repeat using a different volume setting. ) Step 11. Configure fan speed: Press the OSD button on the remote to view the main audio menu. [. . . ]