User manual JBL CVSAT50

[. . . ] ® CINEMA VISIONTM CVSAT50, CVCEN50, CVSUB50 OWNER'S GUIDE READ FIRST!Important Safety Precautions! CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: To reduce the risk of electric shock, do not remove cover (or back). Refer servicing to qualified service personnel. CAUTION: To prevent electric shock, do not use this (polarized) plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] Tighten the bolts securely using a Philips screwdriver (not supplied). Do not overtighten, as this might strip the threads, which is not covered by the warranty. Prepare the speaker wire as described on page 8. Remove the rubber strip from the back of the column, revealing the wire-management channel. Thread the two conductors through the hole at the top of the channel. Make sure to preserve the proper polar- ity (+ and ­ connections) by placing the positive conductor on the left, and the negative conductor on the right, looking at the front of the stand column. Use the supplied terminal wrench to loosen the red collar of the binding post until the pass-through hole underneath it is revealed. Insert the bare end of the positive wire through the hole, then screw the collar down until it is tight. Follow the same procedure to connect the negative wire to its terminal. Slowly lower the mounting bracket on the satellite onto the top of the metal column of the CVTS50 stand. Carefully press the rubber strip in place over the wire-management channel, being careful to keep the speaker wire in the channel and to avoid pinching it with the rubber strip. 5 MOUNTING THE SATELLITES ON OPTIONAL FLOOR STANDS Important Safety Note: The supplied floor stand adaptors facilitate installation with a variety of generalpurpose floor stands available from many manufacturers. Prepare the speaker wire as described on page 8, keeping the (+) conductor to the left and the (­) conductor to the right as you face the wall. Mount the attachment plate into a wood stud on the wall, using three #10 panhead wood screws at least one inch long (not supplied). Make sure that all three screws are driven into the stud and not into drywall. If the bracket needs to be mounted in drywall, the customer is responsible for selecting and using appropriate wall anchors and screws. Making sure to preserve the proper polarity (+ and ­ connections), use the supplied terminal wrench to loosen the red collar of the binding post until the pass-through hole underneath it is revealed. Insert the bare end of the positive wire through the hole, then screw the collar down until it is tight. Follow the same procedure to connect the negative wire to its terminal. Carefully lower the speaker onto the bracket so that the mounting bracket on the satellite slides over the wall attachment plate until the metal spring clip engages in the square hole in bracket part B. Shown without speaker attached to bolts. ATTACHING THE CRADLE TO THE CENTER SPEAKER Important Safety Notes: · The CVCEN50 cradle is only intended for use with the CVCEN50 speaker. Attempting to use the cradle with any other model speaker is unsafe and may result in personal injury and damage to the equipment. · The cradle must be placed in a safe location, protected from young children and pets who might topple it, possibly resulting in serious injury. Never place the cradle so that any part of it is sticking out over the edge of the table, shelf or other surface underneath it. · If you intend to install the CVCEN50 speaker on top of the JBL Cinema Vision plasma television, do not use the cradle. [. . . ] If there is no sound from the center speaker: · Check all wires and connections between receiver/ amplifier and speaker. Make sure none of the speaker wires are frayed, cut or punctured, or touching each other. · If your receiver/processor is set in Dolby Pro Logic mode, make sure the center speaker is not in phantom mode. · If your receiver/processor is set in one of the Dolby Digital or DTS modes, make sure the receiver/processor is configured so that the center speaker is enabled. [. . . ]