User manual JBL EC25 CHERRY EC25CH

[. . . ] Slight variations will not diminish your listening pleasure. All of the Northridge E Series loudspeakers referred to in this guide are video-shielded and can safely be placed near a television. (0­0. 6m) 40o ­ 60o As front speakers 5 ­ 6 ft. (1. 5­1. 8m) The EC25 center channel loudspeaker is designed to complement all of the Northridge E Series loudspeakers. [. . . ] Check that the loudspeaker is firmly locked onto the screws by gently pulling the speaker down and forward. · Proper selection of mounting hardware and installation of the wall brackets are the responsibility of the customer. · This product is not intended for ceiling mounting. Two Number 8 round head or pan head screws should be used per loudspeaker. The screw head should be between 5/16 inch (8mm) and 1/4 inch (6. 3mm) in diameter, and the screw should be at least 2 inches (50mm) in length. When installing screws in any wall, always use properly selected wall anchors. Attach two of the four self-adhesive rubber pads that came with the E10 loudspeaker to the back of the enclosure in the two bottom corners so that the cabinet is spaced evenly from the wall. Select a suitable mounting location on a wall. (The ceiling is not a suitable mounting location. ) Drill two pilot holes, appropriately sized for the specific self-tapping screw or wall anchor that you will be using. The holes should be 8 inches (203mm) apart. The holes should be 3/4" (19mm) below where you want the top of the enclosure to be positioned. Use a carpenter's level to ensure that the holes are even and that the speaker will mount on the level. Install the two screws into either a wooden wall stud or 8" (203mm) 1/8" (3mm) TROUBLESHOOTING If there is no sound from any of the speakers: · Check that receiver/amplifier is on and that a source is playing. · Review proper operation of your receiver/amplifier. If there is no sound coming from one speaker: · Check the "Balance" control on your receiver/amplifier. · Check all wires and connections between receiver/amplifier and speakers. Make sure no wires are touching other wires or terminals and creating a short circuit. · Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. · In Dolby* Digital or DTS® mode, make sure that the receiver/processor is configured so that the speaker in question is enabled. · Turn off all electronics and switch the speaker in question with one of the other speakers that is working correctly. Turn everything back on, and determine whether the problem has followed the speakers, or has remained in the same channel. [. . . ] · Review the operation of your DVD player and the jacket of your DVD to make sure that the DVD features the desired Dolby Digital or DTS mode, and that you have properly selected that mode using both the DVD player's menu and the DVD disc's menu. SPECIFICATIONS E10 Description 2-Way 4" wall-mount/bookshelf Maximum Recommended Amplifier Power** 100W Power Handling (Continuous/Peak) 50W/200W Nominal Impedance 8 Ohms Sensitivity (2. 83V/1m) 86dB Frequency Response (­3dB) 75Hz ­ 20kHz Crossover Frequency 2000Hz High-Frequency Transducer 3/4" (19mm) Titanium-laminate dome, shielded Low-Frequency Transducer 4" (100mm) PolyPlas, TM shielded Baffle Low diffraction, IsoPowerTM Port FreeFlowTM flared Network Straight-Line Signal PathTM (SSP) Terminals Gold-plated, 5-way binding posts Dimensions (H x W x D) 10" x 10-1/8" x 5-1/4" 254mm x 257mm x 133mm Weight Per Speaker 8 lb/3. 6kg Declaration of Conformity E20 Description 2-Way 5" bookshelf Maximum Recommended Amplifier Power** 125W Power Handling (Continuous/Peak) 60W/240W Nominal Impedance 8 Ohms Sensitivity (2. 83V/1m) 86dB Frequency Response (­3dB) 68Hz ­ 20kHz Crossover Frequency 3000Hz High-Frequency Transducer 3/4" (19mm) Titanium-laminate dome Low-Frequency Transducer 5" (130mm) PolyPlas, TM shielded Baffle Low diffraction, IsoPowerTM Port FreeFlowTM flared Network Straight-Line Signal PathTM (SSP) Terminals Gold-plated, 5-way binding posts Dimensions (H x W x D) 10-7/8" x 6" x 8-1/8" 275mm x 153mm x 206mm Weight Per Speaker 7 lb/3. 2kg EC25 Description 2-Way dual 5" center Maximum Recommended Amplifier Power** 150W Power Handling (Continuous/Peak) 75W/300W Nominal Impedance 8 Ohms Sensitivity (2. 83V/1m) 90dB Frequency Response (­3dB) 80Hz ­ 20kHz Crossover Frequency 4000Hz High-Frequency Transducer 3/4" (19mm) Titanium-laminate dome, shielded Low-Frequency Transducer Dual 5" (130mm) PolyPlas, TM shielded Baffle Low diffraction, IsoPowerTM Port FreeFlowTM flared Network Straight-Line Signal PathTM (SSP) Terminals Gold-plated, 5-way binding posts Dimensions (H x W x D) 6-7/8" x 18" x 10" 175mm x 457mm x 254mm Weight Per Speaker 15. 6 lb/7. 1kg We, Harman Consumer International 2, route de Tours 72500 Chateau-du-Loir France declare in own responsibility, that the products described in this owner's manual are in compliance with technical standards: EN 50081-1:1992 EN 50082-1:1997 Gary Mardell Harman Consumer International Chateau-du-Loir, France 2/03 PRO SOUND COMES HOMETM JBL Consumer Products, 250 Crossways Park Drive, Woodbury, NY 11797 8500 Balboa Boulevard, Northridge, CA 91329 2, route de Tours, 72500 Chateau-du-Loir, France 800. 336. 4JBL (4525) (USA only) www. jbl. com © 2003 Harman International Industries, Incorporated JBL is a registered trademark of Harman International Industries, Incorporated. 406-000-01530 * Trademark of Dolby Laboratories. DTS is a registered trademark of Digital Theater Systems, Inc. ** The maximum recommended amplifier power rating will ensure proper system headroom to allow for occasional peaks. [. . . ]