User manual JBL ES250P (220-240V)

[. . . ] Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. [. . . ] Plug the transmitter module's power supply into the wall outlet, and connect the included power cord to the transmitter A. Make sure the Transmitter Antenna 9 is extended upward. Set the ID code on the transmitter and subwoofer (B and 4) to the same position, as described on page 6. When connected properly, the LED on the top of the subwoofer will be orange. Set the Low-Pass Selector 3 to the "Off" position. NOTE: Some receivers have two subwoofer outputs. In that case, use either connector. L R LFE Sub In Line In If your receiver/processor does not contain a Dolby Digital or DTS processor, but has subwoofer outputs: RECEIVER/PROCESSOR Level Crossover [Hz] Wireless ID Code Off On Low-Pass L R LFE Sub In Line In NOTE: If your receiver/processor has only one sub out, you may use either the L or R input. 5 English OPERATION Power On Connect your signal source (such as an A/V receiver or preamplifier) to the transmitter (if using a wireless connection) or to the subwoofer (if using a wired connection). While you would ordinarily use the short cable to connect to the transmitter or the long one to connect to the subwoofer, either cable can be used, depending on proximity to the signal source. There is no need or benefit gained from connecting the same source to both the transmitter and the subwoofer. However, you could connect two separate sources to the subwoofer by utilizing both its wired and wireless connections. Both signals will essentially be mixed and outputted by the subwoofer. Plug your transmitter's (if using a wireless connection) and subwoofer's AC cord into a wall outlet. Do not use the outlets on the back of the receiver for the subwoofer. Initially set the Subwoofer-Level Control 6 to the "min" position. Turn on your sub by pressing the Power Switch 0 on the rear panel. Turn on your entire audio system and start a CD or movie soundtrack at a moderate level. Auto On/Standby Transmitter (Wireless Connection Only): The Status LED (not shown) will be lit in red when the unit is in Standby. When the transmitter receives an audio signal from the source, it will immediately turn on and the LED will turn to blinking green or solid green: RED = STANDBY (No signal detected, transmitter off) GREEN (BLINKING) = Transmitter is on but has not established a link with the wireless sub GREEN (SOLID) = Transmitter is on and has already established a link with the wireless sub The transmitter will automatically enter Standby mode after approximately 10 minutes when no signal is detected from your system. Subwoofer: With the Power Switch 0 in the ON position, the Status LED on the top will remain lit to indicate the On/Standby mode of the subwoofer. RED = STANDBY (No signal detected, Amp Off) GREEN = SUB ON (Wired signal detected, Amp On) ORANGE = SUB ON (Wireless link with transmitter active) The subwoofer will automatically enter the Standby mode after approximately 10 minutes when no signal is detected from your system. [. . . ] In the event that your subwoofer ever needs service, contact your local JBL dealer, or visit www. jbl. com for a service center near you. SPECIFICATIONS Frequency Response Amplifier RMS Power Amplifier Peak Dynamic Power Crossover Frequency ES150PW 27Hz ­ 150Hz 300 Watts 500 Watts 50Hz ­ 150Hz; 24dB/octave continuously ajustable when activated 250mm (10") PolyPlasTM Up to 22m (75'), depending upon conditions 2. 4GHz 457mm x 337mm x 409mm (18" x 13-1/4" x 16-1/8") 95mm x 124mm x 100mm (3-3/4" x 4-7/8" x 3-15/16") 17. 7kg (39 lb) 0. 2kg (0. 5 lb) ES250PW 25Hz ­ 150Hz 400 Watts 700 Watts 50Hz ­ 150Hz; 24dB/octave continuously ajustable when activated 300mm (12") PolyPlasTM Up to 22m (75'), depending upon conditions 2. 4GHz 502mm x 400mm x 454mm (19-3/4" x 15-3/4" x 17-7/8") 95mm x 124mm x 100mm (3-3/4" x 4-7/8" x 3-15/16") 19. 5kg (43 lb) 0. 2kg (0. 5 lb) Driver Operating Range RF Operating Frequency Subwoofer Dimensions (H x W x D) Transmitter Dimensions (H x W x D) Subwoofer Weight Transmitter Weight The Peak Dynamic Power is measured by recording the highest center-to-peak voltage measured across the output of a resistive load equal to minimum impedance of the transducer, using a 50Hz sine wave burst, 3 cycles on, 17 cycles off. Declaration of Conformity Declaration of Conformity We, Harman Consumer Group, Inc. 2, route de Tours 72500 Château du Loir France declare in own responsibility that the product described in this owners manual is in compliance with technical standards: EN 61000-6-3:2001 EN 61000-6-1:2001 We, Harman Consumer Group, Inc. 2, route de Tours 72500 Château du Loir France declare in own responsibility that the product described in this owners manual is in compliance with technical standards: EN 55013:2001+A1:2003 EN 55020:2002+A1:2003 EN 61000-3-2:2000 EN 61000-3-3:1995+A1:2001 EN 60065:2002 Laurent Rault Harman Consumer Group, Inc. Château du Loir, France 6/08 Laurent Rault Harman Consumer Group, Inc. [. . . ]