User manual JBL ESC 300 (220-240V)

[. . . ] Speaker Placement Satellites Subwoofer 0-2 ft. Mounting Remote Sensor to Center Speaker. If desired, the remote sensor may be placed anywhere using the supplied double-sided tape. Center speaker. Place remote sensor at bottom of center speaker. Insert support leg through remote sensor and into speaker. Surround Speakers 5 ­ 6 ft. Mounting Options Satellites and Surrounds On shelves. On the wall. WB300 or WB300WHT (white). On optional stands. Speaker Connections (rear panel of subwoofer) Center Left Front Right Front TM SUB300 JBL, Incorporated, Northridge, CA For use with ESC300 System A Harman International Company INPUTS AUX VIDEO TV or VCR RIGHT LEFT Audio Output OUTPUTS RIGHT Right Left FRONT SPEAKERS CENTER LEFT Remote Sensor RIGHT SURROUND SPEAKERS LEFT Additional Audio Source Audio Output WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVISI RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR REMOTE SENSOR INPUT Right Left AC POWER ON / STANDBY OFF CAUTION: REPLACE WITH SAME TYPE FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE. Left Surround AC 230V ~ 50Hz Right Surround Manufactured under license from Dolby Laboratories Licensing Corporation. [. . . ] Press (­) on the remote control to decrease the relative volume of the surround channels. Balance Press (R) on the remote control to decrease the volume of the left channel. Press (L) on the remote control to decrease the volume of the right channel. 8. Treble Press (+) to increase the level of high-frequency information. Press (­) to decrease the level of high-frequency information. Bass Press (+) to increase the level of low-frequency information. Press (­) to decrease the level of low-frequency information. 10­14. Surround Modes From the remote, press one of these buttons to directly choose the desired surround mode (see "Surround Modes" section). From the front panel, press (Surround Mode) to cycle between the surround modes. Input Selector From the remote, press either (Aux) or (Video) to select the desired input. From the front panel, press (Input) to select the desired input. 17 18 20 19 21 22 23 24 25 Pro Logic AUX Phantom VIDEO Simulated INPUT SURROUND MODE VOLUME Stereo 3 Stereo ON STANDBY 26 27 1 MUTE 15/16 10 4 Front Panel Indicators 17­18. Input Either Video or Aux will illuminate, depending on which input is chosen. Surround One of these will illuminate, depending on which surround mode is chosen. Status Bar Indicators These LEDs show the relative setting of volume, balance, center level, surround level, bass and treble controls (see "Status Bar Indicators" section). On This will illuminate when the Master On/Off is switched to On/Standby and a signal is present. Standby This will illuminate when the Master On/Off is switched to On/Standby and a signal is not present. Mute Symbol This will flash whenever the Mute feature is engaged. Status Bar Indicators LED Bar Indicators illuminate in response to adjustments in volume, balance, center level, surround level, bass, and treble controls. Volume Increase Decrease Bass, Treble, Center Level, and Surround Level Increase Decrease 0dB 0dB Balance Left Right 0dB 0dB Surround Modes Dolby Pro Logic Use this mode for films recorded using Dolby Pro Logic Surround. The surround channels have a 20-ms delay. Phantom This mode creates surround sound from stereo recordings. The center channel is not used and the surround channels have a 20-ms delay. Simulated This mode provides surround sound with no delay for the surround speakers. 3-Stereo Mode Use this mode to play back Pro Logic-encoded films when you do not want the surround channels to play. [. . . ] If it is not, try the Phantom or Simulated surround mode. If there is no sound from the center speaker, check the following: · Make sure that the processor is in the Pro Logic, 3 Stereo, or Simulated mode. If it is in Phantom or Stereo mode, the center speaker will not play. · Check the connections between the subwoofer and the center speaker. [. . . ]