User manual JBL FM SUB

[. . . ] FM52, FM62, FM82, FM65C & FM8SUB simple set-up guide thank you for choosing JBL. For over 50 years, JBL has been involved in every aspect of musical and film recording and reproduction, from live performances to monitoring the recordings you play in your home, car, or office. We're confident that the you have chosen will provide every note of enjoyment that you expected ­ and that when you think about purchasing additional audio equipment for your home, car, or office you will once again choose JBL. [. . . ] Installation The FM Series flush-mount speakers were designed to be easily installed. However, if you are unsure of your ability to properly install these loudspeakers, please contact your dealer or a qualified installer. Tools Needed Phillips #2 screwdriver Measuring tape Utility knife Pencil Carpenter's level Awl FM52, FM62, FM82 Installation Kit Template Speaker frame Thread-forming screws Retainer clips Mounting brackets Existing Construction Level 1-1/2" 1-1/2" 1-1/2" Template Tape Step One: Remove the grille from the speaker frame. Step Two: Determine the correct speaker location. Step Three: Determine the speaker-frame location. Kerf Line Step Four: Cut the dry wall. Step Five: Place the mounting bracket on the speaker frame using the mounting guides (marked 3/8" , 1/2" 5/8" and 3/4") corre, , sponding to the thickness of the dry wall. Step Six: Place the frame assembly in the wall. Step Seven: Connect the speaker wires to the baffle assembly and install baffle assembly in frame. Do not overtighten the baffle screws. Step Eight: Replace the metal grille. New Construction 1-1/2" 1-1/2" 1-1/2" Step One: Remove the grille from the speaker frame. Step Two: Attach the proper mounting bracket, marked and preset at 3/8" 1/2" 5/8" and 3/4" to the , , , speaker frame. Step Three: Determine the correct speaker location. Step Four: Nail or screw the speaker frame assembly to the wall studs and route the wires through the frame opening. After the Drywall is Installed Step Five: Cut the drywall. Step Six: Connect the speaker wires to the baffle assembly and install baffle assembly in frame. Do not overtighten the baffle screws. Step Seven: Replace the metal grille. FM8SUB 1-1/2" 1-1/2" 1-1/2" Step One: Remove the grille from the subwoofer frame. Step Two: Determine the correct subwoofer location. Step Three Cut the drywall. Step Four: Loosen the eight phillips head screws until the locking tabs turn inward. Step Five Connect the speaker wires to the baffle assembly. Step Six: Place the subwoofer in the wall. Step Seven: Screw down each of the eight phillips head screws. The tabs will swivel into place and secure the unit to the rear surface of the drywall. Step Eight Replace the metal grille. FM65CX 1-1/2" 1-1/2" Step One: Remove the grille from the speaker frame. Step Two: Determine the correct speaker location in the ceiling. Step Three: Cut the drywall. Step Four: Remove 4 phillips head screws that attach speaker to frame. Step Five: Loosen the three phillips head screws on the frame, until the locking tabs turn inward. Step Six: Place the frame assembly in the wall. Step Seven: Screw down each of the three phillips head screws. The tabs will swivel into place and secure the unit to the rear surface of the drywall. Step Eight: Connect the speaker wires to the speaker. Step Nine: Reinstall speaker in frame, using 4 phillips head screws. Step Ten: Replace the metal grille. Painting the Speaker Frame and Grille FM Series loudspeakers can be painted to match any style of decor. If you wish to change their color, the satin finish on the grille and frame will function as a primer coat. Before painting install the paint guard (in the assembly kit) securely into the recess in the baffle. This will protect the speaker components and baffle from paint residue. Use a high-quality spray paint, and apply a thin coat of color. Be certain the grille perforations remain free of paint. Filling them with paint will diminish the sound quality. Note: Gently remove the acoustical blanket from the back of the grille before painting. Reattach the acoustical blanket after the paint has dried. Troubleshooting If there is no sound from either of the speakers, check the following: · Receiver/amplifier is on and a source is playing. · Check all wires and connections between receiver/amplifier, in-wall room volume control and speakers. Make sure none of the speaker wires are frayed, cut, or punctured. [. . . ] We do not recommend sustained operation at these maximum power levels. Declaration of Conformity We, JBL Europe A/S Kongevejen 194B DK-3460 Birkerød DENMARK declare in own responsibility, that the products described in this owner's manual are in compliance with technical standards: JBL Incorporated 8500 Balboa Boulevard, Northridge, CA 91329 1-800-336-4JBL (4525) (USA only) 1996 JBL, Incorporated. JBL is a registered trademark of JBL, Incorporated. FMOM EN 50 081-1/1992 EN 50 082-1/3. 1995 © Steen Michaelsen JBL Europe A/S Birkerød. [. . . ]