User manual JBL GT5-1202BR

[. . . ] Figure 1 03 ANGLE MOUNT 2 1 Important Paperwork Before proceeding, be sure to put the sales receipt from your JBL Component System purchase in a safe place. It is necessary to validate your Limited Warranty. Having access to the receipt is also valuable for insurance purposes and when it comes time to resell your vehicle. 1 Line up tab with slot on bracket 2 Push tweeter into bracket and turn clockwise 04 2 1 IN-LINE CROSSOVER (DO NOT CUT OR BYPASS) GTC04 WIRING HARNESS Typical installation of the GT4. 0c and GT5. 0c woofers with grilles as shown in Figure 2a. FLUSH MOUNT 1 Line up tab with slot on bracket 2 Push tweeter into bracket and turn clockwise CONNECT TO AMPLIFIER Trim Ring Lead from GTC04 tweeter Small 0. 11" (-) Terminals Connect to Amplifier or head unit Attach to two outermost tabs Car Door Large 0. 25" (+) Terminals Grille Screen Figure 2a. Grille mounting Figure 2 Midwoofer Terminal Block Tweeter Output Level The GTC04 is a very efficient tweeter. [. . . ] If there is a need to lower the tweeter output level, a pair of 4 ohm / 5 watt resistors can be connected in series with the GTC04 as shown in Figure 3. To avoid short circuits, make sure that heat-shrink tubing or electrical tape is used to cover all exposed wiring. The in-line crossover acts as a high-pass filter as well as a protection device that keeps the tweeter from being over-exerted by low frequencies that it was not designed to reproduce. Under normal circumstances this crossover should not be bypassed or removed for any reason. Bypass the installed capacitor only when using an outboard active crossover or a custombuilt passive crossover set above 5kHz. IN-LINE CROSSOVER (mylar capacitor) 05 cut wire here after capacitor 4 ohms / 5 watt (min) resistor (sold separately) Figure 3 06 Installation of the GT4. 0c woofer as shown in Figures 4a and 4b. Mounting Ears Removed Figure 4a Removable Mounting Ears on GT4. 0c Bend up and down repeatedly to break off or use tin snips. · Some Toyota installations may require mounting ears to be removed from opposite sides. · Some European car installations may require all four ears to be removed. Figure 4b Two-Screw Mounting Configuration Figure 5a Installation of the GT6. 0c woofer with the Intermount II (pat. pend. ) mounting system is shown in Figures 5a, b, c. Figure 5c 07 Hole Cutout Match Notch on Speaker with Notch on Trim Ring Mounting Ring Mounting Hooks Rotate to Lock Foam Gasket Mounting Slots Rotate to Lock Slots for Mounting Hooks Rotate to Lock Figure 5b Foam Gasket Mounting Ring Grille Trim Ring Grille Screen Mounting Hooks Front View Mounting for US 6-1/2" Honda/Toyota Factory Location Rear View Custom Door Mounting with Grille Screw Patterns Fit DIN (European) 165/170mm Mounting Holes 08 Figure 5d Figure 5e Hole Cutout Clips Mounting the GT6. 0c woofer in 165/170mm DIN (European) installations using the Intermount II clips shown in Figures 5d and 5e. Mounting Surface Front Mounting Rear Mounting Component Placement Because of the JBL Component System's small size and extremely versatile mounting options, there are an almost infinite number of placement options to achieve excellent sound quality in any vehicle. Please consider the following statements to help you get the most from your system. The most spacious stereo image is achieved when the left and right speaker systems are placed as wide apart as possible. 2. The best center image will be achieved when the distance from the left speaker and the right speakers are as equal as possible from your listening position. Check for adequate speaker basket clearance before considering this location! 11 + Right Channel 12 A Note on Power Handling As a result of their high efficiency, all JBL loudspeakers will produce reasonable volume levels in the automotive environment using very little amplifier power. However, the use of a small amplifier to attain very high volume levels could lead to overdriving the amplifier. This will generate high distortion levels which can easily damage loudspeakers, even if the rated power of the amplifier is below the rated maximum power handling of the loudspeaker! As a general rule, do not turn up the volume control past the point where you hear distortion in the form of either signal distortion from an overdriven amplifier or mechanical noise from an overstressed speaker. For the best performance and system reliability, you should select an amplifier with an output rating greater than the maximum power likely to be used to generate the desired volume levels. If you want your system "Loud + Clear, " we suggest that you step up to a JBL power amplifier which has an RMS power rating equal to, but not exceeding the Maximum Recommended Amplifier Power listed in the specifications of your specific JBL speaker. This margin of reserve power will ensure that the amplifier will not attempt to deliver more power than its design allows. Your dealer will be happy to point out which high power JBL amplifiers are optimum for your application and listening habits. Following these guidelines will provide virtually distortion-free sound reproduction and long loudspeaker life. WARNING: Playing loud music over 120dB can permanently damage your hearing. The maximum volume levels achievable with JBL components and high power amplification may exceed safe levels for extended listening. When listening at high volume levels, always use hearing protection or turn it down! Specifications Component Systems Model GT6. 0c Grand Touring Automotive 6-1/2" 2-way Component System 1" Titanium Composite Balanced-Drive Neodymium Magnet Tweeter with 1/2" Dome. Surface and Flush Mounting Brackets Supplied Graphite-Reinforced Polytex Woofer Cone with Butyl Rubber Surround GT5. 0c Grand Touring Automotive 5-1/4" 2-way Component System 1" Titanium Composite Balanced-Drive Neodymium Magnet Tweeter with 1/2" Dome. Surface and Flush Mounting Brackets Supplied Graphite-Reinforced Polytex Woofer Cone with Butyl Rubber Surround 4 Ohms 5 ­ 110 Watts RMS 60Hz ­ 21kHz 90dB 2-3/8" 2-1/2" GT4. 0c Grand Touring Automotive 4" 2-way Component System 1" Titanium Composite Balanced-Drive Neodymium Magnet Tweeter with 1/2" Dome. [. . . ] Surface and Flush Mounting Brackets Supplied Graphite-Reinforced Polytex Woofer Cone with Butyl Rubber Surround 4 Ohms 5 ­ 110 Watts RMS 60Hz ­ 21kHz 90dB 2-3/8" 2-1/2" GT4. 0c Grand Touring Automotive 4" 2-way Component System 1" Titanium Composite Balanced-Drive Neodymium Magnet Tweeter with 1/2" Dome. Surface and Flush Mounting Brackets Supplied Graphite-Reinforced Polytex Woofer Cone with Butyl Rubber Surround 4 Ohms 5 ­ 100 Watts RMS 70Hz ­ 21kHz 90dB 1-3/8" 2" 13 Speaker Impedance Recommended Amplifier Power Range Frequency Response Sensitivity Mounting Depth Drop In: Bottom Mount: 4 Ohms 5 ­ 125 Watts RMS 50Hz ­ 21kHz 91dB 2-3/16" 2-9/16" Warranty Terms: 1 Year Transferable Limited Warranty / 2 Year Extended Transferable Limited Warranty (USA Only) 14 This is an important document. Attach your bill of sale to this page and keep it in a safe place. The JBL warranty remains in effect for one year from the date of the first consumer purchase unless installed by an authorized JBL dealer. [. . . ]