User manual JBL JBL82

[. . . ] If this is a concern, these speakers should be anchored to the wall behind them, using the same procedures and hardware customary for anchoring bookcases and wall units. The customer is responsible for proper installation and proper selection of hardware. The supplied self-adhesive rubber feet may be attached to the bottom corners of your speakers to protect your furniture. Place pads here This model is shipped with four self-adhesive nonskid pads that are to be used when the loudspeaker is intended to be placed on a smoothsurfaced floor, such as tile or hardwood. Gently lay the speaker on its side (not its front or back) on a soft, nonabrasive surface. [. . . ] DO NOT attach the pads if the speaker will be placed on carpeting. NEVER drag the speaker to move it, as this will damage the pads, the feet and/or the wood cabinet itself. Always lift the speaker and carry it to its new location. MODEL: BALBOA 30 Without pad With pad SPEAKER CONNECTIONS Speakers and electronics terminals have corresponding (+) and (­) terminals. It is important to connect both speakers identically: (+) on the speaker to (+) on the amplifier and (­) on the speaker to (­) on the amplifier. Wiring "out of phase" results in thin sound, weak bass and poor imaging. With the advent of multichannel surround sound systems, connecting all of the speakers in your system with the correct polarity remains equally important in order to preserve the proper ambience and directionality of the program material. To use the binding-post speaker terminals, unscrew the colored collar until the pass-through hole in the center post is visible. Insert the bare end of the wire through this hole; then screw the collar down until the connection is tight. The hole in the center of each collar is intended for use with banana-type connectors. · Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. · In Dolby* Digital or DTS® modes, make sure that the receiver/processor is configured so that the speaker in question is enabled. · Turn off all electronics and switch the speaker in question with one of the other speakers that is working correctly. Turn everything back on, and determine whether the problem has followed the speaker, or has remained in the same channel. If the problem is in the same channel, the source of the problem is most likely with your receiver or amplifier, and you should consult the owner's manual for that product for further information. If the problem has followed the speaker, consult your dealer for further assistance or, if that is not possible, visit www. jbl. com for further information. · Make sure the polarities (+ and ­) of the left and right "Speaker Inputs" are connected properly. · If your system includes a powered subwoofer, make sure it is connected correctly, plugged into an active AC outlet and turned on. See the owner's guide for your subwoofer for more information. [. . . ] See the owner's guide for your subwoofer for more information. · If your system does not include a powered subwoofer, consider adding one for use with digital ". 1" surround formats. Declaration of Conformity We, Harman Consumer Group International 2, route de Tours 72500 Chateau-du-Loir France declare in own responsibility that the products described in this owner's manual are in compliance with technical standards: EN 61000-6-3:2001 EN 61000-6-1:2001 Gary Mardell Harman Consumer Group International Chateau-du-Loir, France 1/05 SPECIFICATIONS JBL82 Description 2-Way 130mm (5") bookshelf Maximum Recommended Amplifier Power** 125W Power Handling (Continuous/Peak) 60W/240W Nominal Impedance 8 Ohms Sensitivity (2. 83V/1m) 86dB Frequency Response (­3dB) 68Hz ­ 20kHz Crossover Frequency 3000Hz High-Frequency Transducer 19mm (3/4") Titanium-laminate dome Low-Frequency Transducer 130mm (5") Pure-cellulose fiber cone, shielded Baffle Low diffraction, IsoPowerTM Port FreeFlowTM flared Network Straight-Line Signal PathTM (SSP) Terminal 5-Way binding posts Dimensions (H x W x D) (With grille) 259mm x 165mm x 210mm 10-13/16" x 6-1/2" x 8-1/4" Weight per Speaker 3. 9kg/8. 5 lb BALBOA 30 Description 3-Way 170mm (6") floorstanding Maximum Recommended Amplifier Power** 150W Power Handling (Continuous/Peak) 80W/320W Nominal Impedance 8 Ohms Sensitivity (2. 83V/1m) 90dB Frequency Response (­3dB) 47Hz ­ 20kHz Crossover Frequencies 600Hz, 3500Hz High-Frequency Transducer 19mm (3/4") Titanium-laminate dome Midrange Transducer 100mm (4") Pure-cellulose-fiber cone, shielded Low-Frequency Transducer 170mm (6") Pure-cellulose-fiber cone, shielded Baffle Low diffraction, IsoPower Port FreeFlowTM flared Network Straight-Line Signal PathTM (SSP) Terminals 5-Way binding posts Dimensions (H x W x D) (With grille and feet) 889mm x 229mm x 321mm 35" x 9" x 12-5/8" Weight per Speaker 14. 5kg/32 lb BALBOA CENTER Description 2-Way dual 130mm (5") center Maximum Recommended Amplifier Power** 150W Power Handling (Continuous/Peak) 75W/300W Nominal Impedance 8 Ohms Sensitivity (2. 83V/1m) 90dB Frequency Response (­3dB) 80Hz ­ 20kHz Crossover Frequency 3500Hz High-Frequency Transducer 19mm (3/4") Titanium-laminate dome, shielded Low-Frequency Transducer Dual 130mm (5") pure-cellulose fiber cone, shielded Baffle Low diffraction, IsoPowerTM Port FreeFlowTM flared Network Straight-Line Signal PathTM (SSP) Terminals 5-Way binding posts Dimensions (H x W x D) (With grille) 170mm x 479mm x 260mm 6-11/16" x 18-7/8" x 10-1/4" Weight per Speaker 6. 9kg/15. 2 lb PRO SOUND COMES HOMETM JBL Consumer Products, 250 Crossways Park Drive, Woodbury, NY 11797 8500 Balboa Boulevard, Northridge, CA 91329 2, route de Tours, 72500 Chateau-du-Loir, France 516. 255. 4JBL (4525) www. jbl. com © 2005 Harman International Industries, Incorporated JBL is a registered trademark, and IsoPower, FreeFlow and Straight-Line Signal Path are trademarks, of Harman International Industries, Incorporated. 406-000-05179 * Trademarks of Dolby Laboratories. [. . . ]