User manual JBL K2S5800

[. . . ] OWNER'S GUIDE PROJECT K2 S5800 3-WAY FLOORSTANDING SPEAKER SYSTEM ® ® TABLE OF CONTENTS 3 4 7 10 10 11 12 13 14 17 18 19 PREFACE CHAPTER 1 ­ LEGACY: THE HISTORICAL DEVELOPMENT OF THE JBL PROJECT LOUDSPEAKERS CHAPTER 2 ­ THE PROJECT K2 S5800 LOUDSPEAKER: A TRIUMPH IN ACOUSTICS AND TECHNOLOGY CHAPTER 3 ­ UNPACKING THE PROJECT K2 S5800 SYSTEM CHAPTER 4 ­ SELECTING CABLE CHAPTER 5 ­ AMPLIFIER RECOMMENDATIONS CHAPTER 6 ­ PLACEMENT AND SETUP CONSIDERATIONS CHAPTER 7 ­ PROJECT K2 S5800 SWITCH OPERATIONS CONTROLS AND CONNECTIONS CHAPTER 8 ­ PROJECT K2 S5800 CARE AND MAINTENANCE CHAPTER 9 ­ TROUBLESHOOTING AND SERVICE GUIDE K2 S5800 SPECIFICATIONS 2 PREFACE Thank you for selecting a Project K2 S5800 loudspeaker system. It represents the sum total of our research and developmental efforts in sound reproduction over the last half century. We have labored to create a loudspeaker system with no acoustical or electrical limitations whatsoever. While the Project K2 S5800 loudspeaker is itself a new development, the goal behind it goes right back to the earliest days of the original James B. [. . . ] With Project K2 S5800, it is most important to be able to accommodate the optimum listening area that is defined by the 60° horizontal/ 30° vertical coverage pattern of the horn. The listener should be centered in front of the speakers and furniture should be of an appropriate height so that when the listener is sitting, the ear level is on a vertical plane with the horn (approximately 32 in/ 80cm) as illustrated in Figure 2. CAUTION: Project K2 S5800 is a massive system comprising materials chosen for their density, with its weight concentrated in a relatively narrow area. Verify the integrity of the floor surface before placing and setting up the speakers. If possible, the distance between the speakers should be the same as the distance between each speaker and the listening area. Angle the speaker in toward the listener so that when seated, the listener could look straight into the center of the speaker (Figure 7). As the distance increases between the speakers, increase the inward angle of the speaker. The imaging qualities enable the speakers to be placed relatively far apart from each other. In addition, the low-frequency alignment feature enables placing the speakers near or even in a corner without producing an overabundance of bass. This corner placement ability allows optimum performance even in small rooms. The Project K2 S5800 system can operate fairly close to the wall. Allow enough clearance between the back of each speaker and the wall to allow making the connections on the back of the speaker (approximately 2"­3" is sufficient), and to avoid interference with the performance of the tuned port. Remember that these speakers weigh close to 185 lb (84kg) each and cannot be easily moved. FLOOR REQUIREMENTS The floor in the location selected for setting up the Project K2 S5800 speakers must be capable of supporting a load of 185 lb (84kg). Because of the coupling effect of the stainless steel feet, a flat, hard surface such as wood or linoleum is preferable. However, the design of the loudspeaker's coupling system, along with the speaker's extreme weight, should result in excellent performance on any surface, even on carpets. To prevent indentations on wood or linoleum floors caused by the weight of the loudspeaker, always utilize the enclosed coasters. Do not set up the Project K2 S5800 system directly on a ceramic tile floor; the concentrated weight might cause the tiles to crack. 12 Figure 7. Room placement of K2 S5800 speaker system. CHAPTER 7 ­ PROJECT K2 S5800 SWITCH OPERATIONS 0 K2 S580 A CA US ORATED thridge, Nor CORP JBL IN alboa Blvd. 8500 B y equenc High Fr y equenc Low Fr +1dB 0dB -1dB RIM CY T UEN FREQ HIGH MP BI-A / MAL NOR E IR BI-W A D ge, C RATE hrid RPO . Nort INCO Blvd JBL Balboa 00 85 USA y uenc Freq High y uenc Freq Low 800 K2 S5 Figure 8. Access to control panel. The K2 S5800 has two switches mounted on the network panel on the rear of the enclosure. The switches are covered by an access plate which is easily removed by unscrewing the two mounting screws. [. . . ] · Check all wires and connections between the receiver/amplifier and the speakers. Make sure all wires are connected, and are not frayed, cut or punctured. No wires or strands should be touching each other or the shorting bars connected to other terminals. · In digital surround sound modes, make sure that the receiver/ processor is configured so that the speaker in question is enabled. · Check all wires and connections between the receiver/amplifier and the speakers. [. . . ]