User manual JBL LS120P/230 (220-240V)

[. . . ] Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. [. . . ] As a result, specific location of the subwoofer becomes important, and we strongly recommend that you experiment with placement before choosing a final location. Placement will depend upon your room and the amount and quality of bass required (for example, whether or not your room permits placement of the subwoofer near either satellite). Figure 1. This example shows the subwoofer positioned behind the right-channel satellite speaker to re-create the actual location of bass instruments in an orchestra and/or add impact to movie soundtracks. INSTALLING SPIKED FEET Four metal spikes are supplied for use when the speaker is to be placed on a carpeted surface; using them decouples the speaker from the floor to prevent unwanted damping. To insert the spikes, gently lay the speaker on its side (not its front or back) on a soft, nonabrasive surface, and unscrew the rubber-tipped feet (store in a safe place). Each spike then screws into the threaded insert in each corner. Make sure all four spikes are screwed in completely for stability. To protect the surface of uncarpeted floors, set each spike into an included metal coaster. NEVER drag the speaker to move it, as this will damage the spikes, the feet, the wood cabinet itself, and/or the floor. Always lift the speaker and carry it to its new location. 3 English 0012CSK - JBL LS120P OM UK v2. qxp:v 14/01/08 17:12 Side 4 CONTROLS AND CONNECTIONS REAR PANEL 0 Phase Switch 1 LFE/Normal Selector 2 Subwoofer-Level Control 3 Crossover Adjustment 0 4 Power Indicator 1 5 Line-Level/LFE Input 2 6 Power Switch 3 4 5 LS120P/230 6 4 0012CSK - JBL LS120P OM UK v2. qxp:v 14/01/08 17:12 Side 5 SYSTEM CONNECTIONS If you have a Dolby® Digital or DTS® receiver/processor with a low-frequency-effects (LFE) or subwoofer output: Set LFE/Normal switch to "LFE. " LS120P/230 If your receiver/processor does not contain a Dolby Digital or DTS processor, but has subwoofer outputs: Set line-level/LFE switch to "Normal. " NOTE: If your receiver/processor has only one sub out, you may use either the L or R input. LS120P/230 5 English 0012CSK - JBL LS120P OM UK v2. qxp:v 14/01/08 17:12 Side 6 OPERATION POWER ON Plug your subwoofer's AC cord into a wall outlet. Do not use the outlets on the back of the receiver. Initially set the Subwoofer-Level Control 2 to the "min" position. Turn on your sub by pressing the Power Switch 6 on the rear panel. Turn on your entire audio system and start a CD or movie soundtrack at a moderate level. AUTO ON/STANDBY With the Power Switch 6 in the ON position, the Status LED 4 on back will remain lit in red or green to indicate the On/Standby mode of the subwoofer. RED = STANDBY (no signal detected, Amp Off) GREEN = ON (signal detected, Amp On) The subwoofer will automatically enter the Standby mode after approximately 10 minutes when no signal is detected from your system. The subwoofer will then power ON instantly when a signal is detected. During periods of normal use, the Power Switch 6 can be left on. You may turn off the Power Switch 6 for extended periods of nonoperation, e. g. , when you are away on vacation. GETTING STARTED Turn your Subwoofer-Level Control 2 up to the halfway position. If no sound emanates from the subwoofer, check the AC-line cord and input cables. Are the connectors on the cables making proper contact?Is the AC plug connected to a "live" receptacle? [. . . ] If you have a Dolby Digital or DTS processor/receiver, the Low-Pass Frequency is set by the processor/receiver. Consult your owner's manual to learn how to view or change this setting. MAINTENANCE AND SERVICE The enclosure may be cleaned using a soft cloth to remove fingerprints or to wipe off dust. Stains may be removed with an aerosol cleaner, following its instructions. All wiring connections should be inspected and cleaned or remade periodically. [. . . ]