User manual JBL LS60 [LS60]

[. . . ] The customer is responsible for proper installation and proper selection of hardware. Left Surround Channel Left Rear Channel Center Rear Channel Right Rear Channel Right Surround Channel Figure 2. This overhead view shows a typical home theater plan. Left/right rear channels are for a 7-channel system. The center rear channel is for a 6-channel system. JBL Subwoofer (optional) STEREO Before deciding where to place your speakers, survey your room and think about placement, keeping the following points in mind, using Figure 1 as a guide: · For best results, place the speakers 6'­8' (1. 5m­2. 5m) apart. [. . . ] NEVER drag the speaker to move it, as this will damage the spikes, the feet the wood cabinet itself and/or the floor. ALWAYS lift the speaker and carry it to its new location. HOME THEATER For front-channel use, place one speaker on the left and another on the right, along either side of the television monitor. The JBL LS speakers are primarily designed for use with Plasma, LCD and DLP TV screens, and should not be placed in close proximity of CRT (Cathode Ray Tube) TV sets. For surround-channel use, place speakers on bookshelves or stands alongside the listening position. Final placement depends on room acoustics, availability of space and your listening preference (Figures 2 and 3). In 6- or 7-channel configurations, place the rear channel(s) behind the listening position, as shown in Figures 2 and 3. 2 WIRING THE SYSTEM IMPORTANT: MAKE SURE ALL EQUIPMENT IS TURNED OFF BEFORE MAKING ANY CONNECTIONS For speaker connections, use a high-quality speaker wire with polarity coding. The side of the wire with a ridge or other coding is usually considered positive polarity (i. e. , +). NOTE: If desired, consult your local JBL dealer about speaker wire and connection options. The speakers have coded terminals that accept a variety of wire connectors. The most common connection is shown in Figure 4. To ensure proper polarity, connect each + terminal on the back of the amplifier or receiver to the respective + (red) terminal on each speaker, as shown in Figure 5. Connect the ­ (black) terminals in a similar way. See the owner's guides that were included with your amplifier, receiver and television to confirm connection procedures. SINGLE-STEREO AMPLIFIER Figure 7. DUAL-STEREO AMPLIFIER Speaker Wire Figure 4. This figure shows how to connect bare wires to the terminals. Figure 8. IMPORTANT: DO NOT REVERSE POLARITIES (I. E. , + TO ­ OR ­ TO +) WHEN MAKING CONNECTIONS. DOING SO WILL CAUSE POOR IMAGING AND DIMINISHED BASS RESPONSE. FINAL ADJUSTMENTS Check the speakers for playback, first by setting the system volume control to a minimum level, and then by applying power to your audio system. Play a favorite music or video segment and increase the system volume control to a comfortable level. NOTE: You should hear balanced audio reproduction across the entire frequency spectrum. [. . . ] 3/4" (19mm) Polyester-film ring-radiator, neodymium magnet; EOS waveguide 19-7/16" x 8-3/4" x 13-1/2" (493mm x 222mm x 343mm) 19-5/8" x 8-3/4" x 13-1/2" (499mm x 222mm x 343mm) 29. 8 lb (13. 5kg) LS60 40Hz ­ 40kHz 48Hz ­ 38kHz 75W 150W 300W 150W 87dB 400Hz, 6dB/octave, 2kHz, 8kHz; 24dB/octave 6 Ohms Dual 6-1/2" (165mm) with cast-aluminum frames 2" (50mm) Pure-titanium compression driver, Bi-Radial Horn® 3/4" (19mm) Polyester-film ring-radiator, neodymium magnet; EOS waveguide 39-1/2" x 8-3/4" x 13-1/2" (1004mm x 222mm x 343mm) 40" x 8-3/4" x 13-1/2" (1017mm x 222mm x 343mm) 58. 6 lb (26. 6kg) LS80 35Hz ­ 40kHz 46Hz ­ 38kHz 100W 200W 400W 200W 90dB 400Hz, 6dB/octave, 2. 5kHz, 8kHz; 24dB/octave 6 Ohms Dual 8" (200mm) with cast-aluminum frames 2" (50mm) Pure-titanium compression driver, Bi-Radial Horn® 3/4" (19mm) Polyester-film ring-radiator, neodymium magnet; EOS waveguide 43-1/2" x 10-3/16" x 16-1/2" (1104mm x 259mm x 418mm) 44" x 10-3/16" x 16-1/2" (1117mm x 259mm x 418mm) 78. 5 lb (35. 6kg) Ultrahigh-Frequency Transducer Dimensions (H x W x D) Dimensions (H x W x D) (with feet and pad) Weight per Speaker (net weight) LS CENTER Frequency Response (­10dB) Frequency Response (­3dB) Power Handling (Continuous) Power Handling (Music) Power Handling (Peak) Max. Amplifier Power* Sensitivity (2. 83V/1m) Crossover Frequency Nominal Impedance Low-Frequency Transducers High-Frequency Transducer 50Hz ­ 40kHz 85Hz ­ 38kHz 75W 150W 300W 150W 88dB 2. 5kHz, 9kHz; 24dB/octave 6 Ohms Dual 6-1/2" (165mm) with cast-aluminum frames 2" (50mm) Pure-titanium compression driver, Bi-Radial Horn®. 3/4" (19mm) Polyester-film ring-radiator, neodymium magnet; EOS waveguide 8-1/2" x 26-1/2" x 9-1/4" (217mm x 672mm x 235mm) 9" x 26-1/2" x 9-1/4" (230mm x 672mm x 235mm) 31. 7 lb (14. 4kg) We, Harman Consumer Group, Inc. 2, route de Tours 72500 Château du Loir France declare in own responsibility that the products described in this owners manual are in compliance with technical standards: EN 61000-6-3:2001 EN 61000-6-1:2001 Ultrahigh-Frequency Transducer Dimensions (H x W x D) Dimensions (H x W x D) (with feet and pad) Weight per Speaker (net weight) Declaration of Conformity * The maximum recommended amplifier power rating will ensure proper system headroom to allow for occasional peaks. [. . . ]