User manual JBL P 23T

[. . . ] Automotive Loudspeakers P -4 3 2, P- 5 32 , P -63 2 , P -9 6 32 , P- 96 3 3, P - 33 2, P- 6 4 32 , P- 7 5 32 , P -23 t & P-K it Ow n er 's M a nu al GE NU I NE J BL Thank you for purchasing JBL's Power SeriesTM automotive loudspeakers. In order that we may better serve you should you require warranty service on your new speakers, please retain your original purchase receipt and return the enclosed warranty registration card. Important: Installation of automotive stereo components can require extensive experience performing a variety of mechanical and electrical procedures. [. . . ] · For door installations, check the clearance with the windows in both closed and open positions and verify that a mounted speaker will not interfere with the window crank or power-window mechanism. · If mounting speakers near rear-deck torsion bars, glove box or other structural elements, check for clearance first. · Do not mount speakers where they will get wet. Warning: Playing loud music in an automobile can permanently damage your hearing as well as hinder your ability to hear traffic. We recommend listening at low levels while in your car. JBL accepts no liability for hearing loss, bodily injury or property damage resulting from use or misuse of this product. 02 Installation of the P-332, P-6432 and P-7532, as shown in Figure 1. Installation of the P-432, P-532, P-9632 and P-9633, as shown in Figures 2 and 3. Figure 1. Figure 2. Figure 3. Note: The P-332, P-6432 and P-7532 are designed as direct replacements for original-equipment speakers mounted behind factory grilles. Note: If you are mounting the P-532, P-9632 or P-9633 behind factory grilles, omit the grille and grille tray in Figure 2. Note: Some installations may require some or all of the mounting ears to be removed from the P-432. Remove your original speakers first to determine whether any mounting ears must be removed. 03 Installation of the P-632, as shown in Figures 4a and 4b. The P-632 uses JBL's Intermount IIITM mounting system. Intermount IIITM provides for easy installation of these speakers in many standard and nonstandard locations that will accommodate a 6-1/2" speaker. Figure 4a. Figure 4b. Using Intermount IIITM in American and Japanese cars with openings for 6-1/2" speakers. Important: When using the steel mounting rings, you must make sure that the rings are mounted to a completely flat surface. Using Intermount IIITM in European and American 165mm openings or custom-mounting the speaker. 04 Converting the P-432, P-532 and P-632 to a component system using the optional P-Kit (sold separately), as shown on pages 5 and 6. Separating the tweeter and woofer, as shown in Figures 5a and 5b. Figure 5a. Figure 5b. Remove the orange wire cover by inserting a small screwdriver into the notch between the two terminals and prying upwards. Disconnect the tweeter wires from the terminal. Reinstall the cover after removing the tweeter. Detach the tweeter by turning it counterclockwise to unlock it, then pull it away from the woofer while feeding the wires through the pole piece. [. . . ] Connect the wires between the crossover, and between the woofer and tweeter as shown. 06 Specifications P-432 4" 2-Way or Component System with Optional P-Kit Woofer-Cone Material Tweeter-Diaphragm Material Frequency Response Sensitivity Recommended Amplifier Power Range as Multielement Recommended Amplifier Power Range as Component Mounting Depth ThermalumTM NeoGlassTM 65Hz ­ 22kHz 90dB 5W ­ 120W 5W ­ 175W 2" (51mm) P-532 5-1/4" 2-Way or Component System with Optional P-Kit ThermalumTM NeoGlassTM 55Hz ­ 22kHz 90dB 5W ­ 150W 5W ­ 200W 2-1/4" (57mm) P-632 6-1/2" 2-Way or Component System with Optional P-Kit ThermalumTM NeoGlassTM 45Hz ­ 22kHz 91dB 5W ­ 175W 5W ­ 225W 2-1/2" (64mm) P-9632 6" x 9" 2-Way Component System ThermalumTM NeoGlassTM 25Hz ­ 22kHz 92dB 5W ­ 250W N/A 3-1/8" (80mm) P-9633 6" x 9" 3-Way Component System ThermalumTM NeoGlassTM 25Hz ­ 22kHz 92dB 5W ­ 250W N/A 3-1/8" (80mm) P-332 3-1/2" 2-Way Component System Woofer-Cone Material Tweeter-Diaphragm Material Frequency Response Sensitivity Recommended Amplifier Power Range as Multielement Recommended Amplifier Power Range as Component Mounting Depth ThermalumTM NeoGlassTM 70Hz ­ 22kHz 89dB 5W ­ 90W N/A 1-3/4" (45mm) P-6432 4" x 6" 2-Way Plate ThermalumTM NeoGlassTM 65Hz ­ 22kHz 90dB 5W ­ 150W N/A 1-7/8" (48mm) P-7532 5" x 7" 2-Way or Component System with Optional P-Kit ThermalumTM NeoGlassTM 45Hz ­ 22kHz 91dB 5W ­ 175W N/A 2-1/4" (58mm) P-23t Component Tweeter N/A NeoGlassTM 5kHz ­ 22kHz 91dB (with crossover) 5W ­ 100W N/A 7/8" (23mm) P-Kit Conversion Kit for P-432, P-532, P-632, P-7532 N/A N/A N/A N/A N/A N/A 7/8" (23mm) 07 Declaration of Conformity We, JBL Europe A/S Kongevejen 194B DK-3460 Birkerød DENMARK declare in own responsibility, that the products described in this owner's manual are in compliance with technical standards: EN 50081-1:1992 EN 50082-1:1992 Steen Michaelsen JBL Europe A/S Birkerød. 3/99 JBL Consumer Products, 250 Crossways Park Drive, Woodbury, NY 11797 800-336-4JBL (4525) www. jbl. com Part No. [. . . ]