User manual JBL SCS 138 TRIO (220-240V)

[. . . ] X+ 0+ Y2 0 M HZ 4" 8" X+ 0+ Y2 0 M HZ X + 0 + Y 2 0 M HZ OWNER'S GUIDE PRODUCT LINE: Surround Cinema Speakers MODEL NUMBER: TRIO138S D E S I G N G O A L : Bring the thrill of live performance and movie sound to the home environment by calling on JBL's professional engineering leadership. T W E E T E R T Y P E : Titanium-laminate-dome E N C L O S U R E T Y P E : Sealed P R O F E S S I O N A L R E F E R E N C E : Cinema Loudspeaker Series READ THIS! RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: To prevent electric shock, do not remove the grounding plug on the power cord, or use any plug or extension cord that does not have a grounding plug provided. Make certain that the AC outlet is properly grounded. Do not use an adapter plug with this product. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Precautions! facturer's instructions, and should use a mounting accessory recommended by the manufacturer. [. . . ] When placing the unit on a shelf, be certain that the shelf and any mounting hardware can support the product's weight. Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manu- 2 22. Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. To avoid safety hazards, use only the power cord supplied with your unit. If a replacement cord is used, make certain that it is of a similar gauge. We do not recommend using extension cords with this product. As with all electrical devices, do not run power cords under rugs or carpets or place heavy objects on power cords. Damaged power cords should be replaced immediately, by a qualified service technician, with cords meeting factory specifications. When disconnecting the power cord from an AC outlet, always pull the plug; never pull the cord. The power cord of the product should be unplugged from the outlet when left unused for long periods of time. For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 25. Do not overload wall outlets, extension cords, or integral convenience receptacles, as this can result in a risk of fire or electric shock. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. The power-supply cord or the plug has been damaged; or b. Objects have fallen, or liquid has been spilled into, the product; or c. The product has been exposed to rain or water; or d. The product does not operate normally when following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation; or e. [. . . ] · In Dolby* Digital or DTS® modes, make sure that the receiver/processor is configured so that the speaker in question is enabled. If there is no sound from the center speaker: · Check all wires and connections between receiver/ amplifier and speaker. Make sure none of the speaker wires are frayed, cut or punctured. · If your receiver/processor is set in Dolby Pro Logic* mode, make sure the center speaker is not in phantom mode. [. . . ]