User manual JBL SDP-RFD

[. . . ] Never push objects of any kind through any of the ventilation slots. Never spill a liquid of any kind on the unit. This product is equipped with a 3-wire grounding type plug. [. . . ] We have designed this manual to provide a brief overview of the demodulator, as well as to provide the information necessary for safe installation and operation. We trust that the time you invest in reviewing these brief instructions will be rewarded by the best possible performance and longevity of your equipment. 3 NOTE: When power is off, the SDP-RFD AC-3®/RF Demodulator automatically outputs the COAXial digital input. POWER This LED will light whenever power to the unit is supplied and enabled. LOCK This LED will light whenever is present, the LED will rema POWER LOCK RF TIMING AC-3 ®/RF DEMODULATOR RF TIMING 3-position switch which minimizes signal errors, providing optimal timing for specific brands of laser disc players. Recommended Settings Advance Retard Normal Panasonic, Runco Denon All others 4 Front Panel the unit senses an AC-3®/RF signal. When no such signal in off, and the INPUT SELECT LED will light. ADVANCE RETARD NORMAL OPTICAL COAX INPUT SELECT INPUT SELECT 2-position switch for selection of the type of NON-AC-3®/RF digital output you are using from your laser disc player. 5 Connections between the SDP-RFD AC-3®/RF Demodulator and associated equipment should be made with all units UNPLUGGED! RF IN Connect this input to the output with a 75 coax short as possible to min POWER Connect the AC adapter here. Use only the supplied Synthesis MSA AC adapter. PWR CTL PWR CTL SDP-RFD AC-3®/RF DEMODULATOR JBL, INC. NORTHRIDGE, CA 91329 MADE IN U. S. A. POWER INPUT LOOP THRU 9V~, 1A, 50-60Hz SERIAL # USE JBL MSA AC ADAPTER INPUT Connect a 5-pin DIN cord (not supplied) from this input to the SDP-2 PWR CTL Output. This allows the SDP-RFD to power on and off with the SDP-2. If nothing is hooked up here, the unit will turn on whenever the AC adapter is supplied power. This set-up allows use of a switched outlet or continuous power. (As power consumption and heat generation are both minimal, this will not harm the SDP-RFD. ) LOOP THRU Allows the hook-up and power cycling of a ditional components such as the Synthe S Series of power amplifiers. Refer to DIN configuration diagram below. 1 4 2 5 3 1 = Ground 2 = Ground 3 = Power On (cons when the DC-1 is On 4 = Unused 5 = Trigger (programma 6 Rear Panel laser disc player's AC-3®/RF ial cable. Keep this cable as imize RF interference. OUTPUT Connect this S/PDIF output to SDP-2 digital input COAX1 with a 75 coaxial cable. RF IN OUTPUT S/PDIF INPUTS AC-3® S/PDIF COAX OPTICAL THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. dsis the S/PDIF INPUTS Connect this input to the laser disc player's NONAC-3® RF digital output using the appropriate 75 coaxial cable. Because you can switch between these inputs from the front panel, you may use both; which gives you an extra digital input. tant ) ble) 7 LASER DISC PLAYER ANALOG AUDIO OUT L R COAX Audio cable (to other components such as amplifiers) 75 ohm COA (as short as po POWER SDP-RFD AC-3®/RF DEMODULATOR PWR CTL PWR CTL INPUT LOOP THRU 9V~, 1A, 50-60Hz USE SYNTHESIS MSA AC ADAPTER SDP-2 VIDEO VIDEO OUT MONITOR RECORD S-VIDEO TAPE L AUDIO R R INPUTS R R OUTPUTS TUNER CD AUX L TV V-DISC VCR2 L VCR1 ZONE2 RECORD L 8 DIGITAL OUTPUT AC-3®/RF OUTPUT OPTICAL COAX (TOSLINK) (Use one or the other. Most players have only one. ) X cable ssible) RF IN 75 ohm COAX cable OUTPUT OR Optical cable S/PDIF INPUTS AC-3® S/PDIF COAX OPTICAL 5-pin DIN cable (not included) 75 ohm COAX cable ON COAX 1 (digital input) Default input for V-DISC MAIN OUTPUTS SIDE CENTER L OPTICAL R SUBWOOFER 1 2 2 IR IN S/PDIF INPUTS COAX 1 REMOTES PWR CTL REAR FRONT POWER 9 Setup The SDP-RFD AC-3®/RF Demodulator chassis is barely four inches deep to allow it to be positioned adjacent to an AC-3®-capable player's RF output. [. . . ] However, it is good electrical practice to clean all connectors once a year. Clean the exterior surfaces of the unit with a soft, lint-free cloth, dampened with warm water. · · · · · 10 2. SPECIFICATIONS Inputs SPECIFICATIONS 2 2: 1AC-3®/RF via COAX; 2 Digital (1 COAX; 1 Optical) Outputs One (1) Digital via COAX RF Timing 3-position toggle switch, decoder pulse settings Controls and Indicators LEDs indicate operational status Toggle switches for: LD RF Timing: Advance, Retard, Normal Input Select: Optical, COAX Connectors Inputs: 4: 2 RCA (COAX); 1 TOSLINK (Optical); 1 5-pin DIN (PWR CTL) Outputs: 2: 1 RCA (COAX); 1 5-pin DIN (PWR CTL Thru) Power connector: 2. 5mm, 9VAC, 1A General Dimensions: 17. 0"X x 1. 75"H x 4"D Weight: 2. 4 lbs net; 4. 4 lbs shipping Power Requirements: 120VAC, 60Hz or 230VAC, 50Hz. [. . . ]