User manual JBL STC-1

[. . . ] ® STC-1 PROGRAMMABLE TOUCH SCREEN REMOTE OWNER'S GUIDE AND PROGRAMMING MANUAL TABLE OF CONTENTS SECTION _________________________________________ PAGE 1. 0 _______________ INTRODUCTION 1. 1 1. 2 1. 3 1. 4 1. 5 1. 6 1. 7 1. 8 Features Important Notes Getting Started The Touch Screen Display The Special Functions Page Battery Recharging and Control Programming the STC-1 Setting the Access Options 4 4 4 5 5 6 6 7 2. 0 ________CREATING AND EDITING PAGES 2. 1 2. 2 2. 3 2. 4 2. 5 2. 6 2. 7 Creating a Page Editing a Page Placing Buttons on a Page Using the Text Editor Assigning a Page to a Button Removing a Page Assignment from a Button Deleting a Button from a Page 8 8 9 10 11 11 11 3. 0 ________IR EDITOR 3. 1 3. 2 3. 3 3. 4 3. 5 Menu Options Aligning a Remote Control Sending Infrared Commands to the STC-1 Testing Infrared Commands Editing Infrared Commands 12 13 14 14 14 4. 0 ________MACRO EDITOR 4. 1 4. 2 4. 3 4. 4 4. 5 Menu Options Editing a Macro Inserting an Infrared Command Inserting a Time Delay Macro Hints 15 15 16 16 17 5. 0 ________IR CODE BASICS 5. 1 5. 2 5. 3 5. 4 Frequency Modulation Pulsed IR Codes How the STC-1 Learns IR Commands Hints for Learning IR Codes 18 18 18 19 6. 0 ________PROGRAMMING HINTS 6. 1 Summary: Creating Pages 21 7. 0 ________TROUBLESHOOTING 7. 1 Contacting JBL 22 23 24 25 28 8. 0 ________SPECIFICATIONS APPENDIX A: SCREEN TEMPLATES INDEX WARRANTY UNPACKING AND INSPECTION After unpacking the STC-1, save all of the packing materials in case you ever need to ship the unit. Thoroughly inspect the STC-1 and the packing materials for signs of damage. Report any shipment damage to the carrier at once. Report any equipment malfunctions to your dealer. vWARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE. vWARNING THIS UNIT CONTAINS NICKEL-CADMIUM BATTERIES. [. . . ] Each of these infrared commands must be programmed into the STC-1. This is done by using the original remote control (the donor) from a piece of equipment to teach its commands to the STC-1. There are four steps to this learning process: 1. Aligning the donor remote with the STC-1. To begin performing these steps, select the EDIT IR from the Program Options page. The STC-1 will display a list of page names to select from. Either select the desired page or press the EXIT button to cancel the operation. If a page is selected, the STC-1 will display that page along with the ALIGN IR template in the center, as shown below. LEARN IR ALIGN IR 3. 1 Menu Options The options available in this menu are: LEARN IR TEST IR EDIT IR ALIGN IR DELETE IR CANCEL EXIT LEARN IR This function is used for aligning the donor and teaching the STC-1 the infrared commands from the donor. TEST IR This function is used to verify that a command works properly. Edit IR Menu Bar SIGNAL EDIT IR This function is used to modify a command if necessary. See "Hints for Learning IR Codes" on page 19. ALIGN IR This function is used to properly align the donor with the STC-1`s learning window. DELETE IR This function is used to delete an existing command. CANCEL This option is used to close the menu without changing functions. EXIT This option is used to exit the infrared editor. OVERLOAD To select a new function, press anywhere on the screen, then display the menu by touching the top of the menu bar (where it says LEARN IR). 12 IR EDITOR 3. 0 Transmit IR Window IR Learning Window 3. 2 Aligning a Remote Control To ensure that a valid signal is being received, all donor remote controls should be properly aligned with the STC-1`s learning window. This is the small window located on the front of the unit. The STC-1 has an ALIGN IR function to help determine the correct position in front of the learning window. This function is invoked upon entering the Edit IR mode or by selecting ALIGN IR from the pull-down menu while in the Edit IR mode. LEARN IR ALIGN IR To properly align a donor remote control with the STC-1, first make sure the donor remote is at the same height as the learning window. It may be necessary to place the donor remote control on a higher surface than the STC-1. Now press any key on the donor remote control, moving the control back and forth in front of the learning window. The donor remote control is located at the proper distance from the STC-1 when the SIGNAL box is on (darkened) and the OVERLOAD box is off (clear). If neither box is on, the STC-1 is not detecting any infrared signal. If the SIGNAL box will not turn on without turning on the Edit IR Menu Bar OVERLOAD box, you should ignore the overload indicator. [. . . ] Your JBL warranty covers all defects in material and workmanship with the following specified exceptions. These are (1) damage caused by accident, unreasonable use or neglect (including the lack of reasonable and necessary maintenance); (2) damage caused by improper installation or adjustment; (3) damage occurring during shipment (claims must be presented to the carrier); (4) damage to or deterioration of any accessory or decorative surface; (5) damage resulting from failure to follow instructions contained in your owner's manual; (6) damage resulting from the performance of repairs by someone other than an authorized JBL warranty station; (7) any JBL unit on which the serial number has been effaced, modified, or removed; (8) units which have been altered or modified in design, appearance or construction; (9) products sold on an "as-is" or final sale basis. This warranty covers only the actual defects within the product itself, and does not cover the costs of installation or removal from a fixed installation, normal set-up or adjustments, claims based on any misrepresentation by the seller, or performance variations resulting from installation related circumstances such as program source quality or AC power. If your JBL product ever needs service, we may direct you to an Authorized JBL Warranty Station, or ask you to send your unit to the factory for repair in which case we'll also supply a Service Return Authorization and complete shipping instructions. [. . . ]