User manual JBL SVA1600

[. . . ] Please take a moment to complete the enclosed profile card. It enables us to keep you posted on our latest advancements, and helps us to better understand our customers and build products that meet your needs and expectations. JBL Consumer Products Introduction JBL's SVA Series takes advantage of our latest technology to deliver incredibly clean, detailed sound. [. . . ] Hookup Connection Tips Wire Length Up to 20 ft. Recommended Speaker Cable Size 16 gauge 14 gauge 12 gauge or heavier Preparing the Speaker Cable 1. Determine the length of wire necessary to connect your amplifier to the speaker that is farthest away. Remember to allow for extra cable to be able to conceal it under baseboards, or run it around corners. Keep both cable lengths the same in order to help maintain proper signal balance and imaging. Separate about one inch of the two conductors that make up each cable. Then strip off about 3/8" of insulation. Twist each conductor's thin wires into a tightly bunched spiral. Identify a difference between the two conductors. This may be done in various ways, depending upon the type and brand of cable you are using. Some of the More Common Differentiating Marks for Conductors Are: · Different color wire · A strand of thread in one · A colored line on one con- conductor ductor's outer insulation · Raised ribs on one conduc- tor's outer insulation · A printed (+) marking on one of the insulators The terminals on the SVA Series loudspeakers can accept several types of speaker cable connections. Remember to connect the red (+) terminal on the receiver/amplifier to the red (+) terminal on the speaker and the black (­) terminal on the receiver/amplifier to the black (­) terminal on the speaker. ­ HF + ­ HF + High Frequency +2dB 0dB High Frequency +2dB 0dB ­ LF + ­ LF + Bare wire connecting method. Banana/spade connecting method. Standard SVA2100, SVA1800, SVA1600 Right Speaker Receiver/ Amplifier Right ­ HF Left Speaker Left ­ HF + + + ­ + ­ High Frequency +2dB 0dB High Frequency +2dB 0dB ­ LF + ­ LF + SVA1500, SVA Center Right Speaker Receiver/ Amplifier Right Left Left Speaker ­ + + ­ + ­ ­ + Bi-Wiring The SVA2100, SVA1800 and SVA1600 outer connection panel and internal dividing network are designed so that separate sets of speaker cable can be attached to the low-frequency transducer and midrange/high-frequency transducer portions of the dividing network. Bi-wiring provides several sonic advantages and considerably more flexibility in power amplifier selection. ­ HF + High Frequency +2dB 0dB ­ LF + Remove strapping bars. Single-Stereo Amplifier Right Speaker ­ + Receiver/Amplifier Right Left Left Speaker ­ + HF HF High Frequency +2dB 0dB + ­ + ­ High Frequency +2dB 0dB ­ LF + ­ LF + Dual-Stereo Amplifier Right Speaker Amplifier 1 Right ­ HF Amplifier 2 Right Left Left Speaker ­ + Left + + ­ + ­ + ­ + ­ HF High Frequency +2dB 0dB High Frequency +2dB 0dB ­ LF + ­ LF + three. Speaker Angle Adjustment SVA2100, SVA1800, SVA1600 SVA Center The SVA Center terminal cup has an adjustable foot to angle the speaker towards the listening position. Loosen thumbscrew. Slide rod down the desired amount. Tighten thumbscrew. four. Response Contour Adjustment SVA2100, SVA1800, SVA1600 0dB 0dB 0dB ­ + 20 Frequency 20k ­ + 0dB 20 +2dB +2dB Frequency 20k Troubleshooting If there is no sound from any of the speakers, check the following: · Receiver/amplifier is on and a source is playing. · Review proper operation of your receiver/amplifier. If there is no sound coming from one speaker, check the following: · Check the "Balance" control on your receiver/amplifier. [. . . ] · Check all connections between processor/amplifier and each of the speakers. Specifications SVA2100 Frequency Response 40Hz ­ 18kHz (±2dB) 30Hz ­ 20kHz (­6dB) Sensitivity 93dB @ 2. 83 volts/1 meter Recommended Maximum Amplifier Power** 300 watts Impedance 8 ohms nominal Crossover Frequency 1200Hz Dimensions (HxWxD) 43 x 14-1/2 x 20-1/4 inches 1092 x 368 x 514mm Weight 95 lbs/43 kg SVA1800 Frequency Response 50Hz ­ 18kHz (±2dB) 35Hz ­ 20kHz (­6dB) Sensitivity 92dB @ 2. 83 volts/1 meter Recommended Maximum Amplifier Power** 250 watts Impedance 8 ohms nominal Crossover Frequency 1600Hz Dimensions (HxWxD) 38 x 12-1/2 x 16-1/4 inches 965 x 318 x 413mm Weight 75 lbs/34 kg SVA1600 Frequency Response 50Hz ­ 18kHz (±2dB) 38Hz ­ 18kHz (­6dB) Sensitivity 89dB @ 2. 83 volts/1 meter Recommended Maximum Amplifier Power** 200 watts Impedance 8 ohms nominal Crossover Frequency 1750Hz Dimensions (HxWxD) 35-3/4 x 11 x 13-1/2 inches 908 x 279 x 343mm Weight 60 lbs/27 kg SVA1500 Frequency Response 80Hz ­ 18kHz (±2dB) 45Hz ­ 20kHz (­6dB) Sensitivity 88dB @ 2. 83 volts/1 meter Recommended Maximum Amplifier Power** 150 watts Impedance 8 ohms nominal Crossover Frequency 2500Hz Dimensions (HxWxD) 20 x 6-13/16 x 11-1/8 inches 508 x 173 x 283mm Weight 25 lbs/11. 4 kg SVA Center Frequency Response 80Hz ­ 18kHz (±2dB) 45Hz ­ 20kHz (­6dB) Sensitivity 88dB @ 2. 83 volts/1 meter Recommended Maximum Amplifier Power** 150 watts Impedance 8 ohms nominal Crossover Frequency 2500Hz Dimensions (HxWxD) 6-13/16 x 20 x 11-1/8 inches 173 x 508 x 283mm Weight 25 lbs/11. 4 kg Occasional refinements may be made to existing products without notice, but will always meet or exceed original specifications unless otherwise stated. **The maximum recommended amplifier power rating will ensure proper system headroom to allow for occasional peaks. We do not recommend sustained operation at these maximum power levels. Declaration of Conformity RAT CEL EB I NG 0 YEAR S JBL Consumer Products 80 Crossways Park West, Woodbury, NY 11797 8500 Balboa Boulevard, Northridge, CA 91329 1-800-336-4JBL (4525) (USA only) http://www. jbl. com © 1996 JBL, Incorporated. [. . . ]