User manual JBSYSTEMS LIGHT SMP 12.22 V1.0

[. . . ] Sie können sich die Deutsche Version dieses Benutzerhandbuches von unserer Website herunterladen: www. synq-audio. com ® ES: Gracias por comprar este producto SynQ . Puede descargar la versión en Español de este manual de usuario en nuestra página Web: www. synq-audio. com PT: Obrigado por ter adquirido este produto da SynQ®. Pode fazer o download da versão Portuguesa deste manual no nosso website: www. synq-audio. com ® Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user manual. [. . . ] TRIM CONTROL According to the level of the input signal, use this knob to adjust the input to an appropriate level. The best balance of S/N and dynamic range will be achieved if you adjust the TRIM control so that the peak indicator lights occasionally. This control adjusts the channel's MIC input sensitivity between -50dB and -6dB and the line input sensitivity between -30dB and +14dB. AUX CONTROL AUX 1 CONTROL This AUX1 knob controls the signal level that the channel sends to the AUX1 bus. If you are using stereo channels, the signals from the L and R channels are mixed and send to the AUX1 bus. These controls are placed before the channel fader (pré-fader), what means that it's level in not influenced by the position of the channel fader. Pré-fader aux outputs are mainly used to control stage monitors AUX 2 CONTROL The AUX2 knob controls the signal level that the channel sends to the AUX2 bus. If you are using stereo channels, the signals from the L and R channels are mixed and send to the AUX1 bus. The AUX 2 controls can be switched as pré fader or post fader controls. Pré-fader aux outputs are not influenced by the position of the channel fader and are mainly used to control stage monitors. Post-fader Aux outputs are also influenced by the channel faders and are mainly used with effect modules. BALANCE (Stereo Channel) This control adjusts the balance or the L/R position of the stereo input signal. Turning the BALANCE control to the left moves the apparent source toward the MAIN MIX L bus, turning it to the right moves the source toward the MAIN MIX R bus. DSP PROGRAM SELECT SWITCH Turn the program knob to select one of the 100 built-in digital effects. The 24 Bit Digital Effects processor provides high quality effects like Delay, Chorus and Reverb. AUX PRE CONTROL Adjust the level of the signal sent from the internal Digital effect to the AUX1 and AUX2 busses. Like this you can also send for example some effect into your stage monitors 4. DSP ON/OFF SWITCH This switch turns the internal digital effect on/off. SYNQ® 5/20 SMP16. 42 SYNQ® 6/20 SMP16. 42 ENGLISH OPERATION MANUAL ENGLISH CONNECTORS OPERATION MANUAL 17. LEVEL METER SIGNAL SWITCHES These level-meter switches, together with the channel PFL switches, select the signal that is sent to the CONTROL ROOM OUT jacks, the HEADPHONE jack, and the LEVEL METER. , then only the channel's PFL output is sent to the If the input channel's PFL switch is on CONTROL ROOM OUT jacks, the HEADPHONE jack, and the LEVEL METER. If the input channel's PFL switch is off , then the MAIN L/R signal, GROUP1-2 signal or GROUP 3-4 signal can be monitored via the CONTROL ROOM OUT jacks, the HEADPHONE jack, and the LEVEL METER. Use the MAIN or the GROUP switches to select the desired output to listen to. [. . . ] You can use these outputs to connect the power amplifiers for you main speakers, or you can use them when you wish to record the signal that is also influenced by the main output faders. 11. CONTROL ROOM OUTPUT JACKS These unbalanced 1/4" Jack outputs are controlled by the CTRL ROOM /PHONES CONTROL and are generally used to connect a monitoring system. NOTE::The signal monitored by these outputs is selected by the settings of the LEVEL METER SIGNAL SWITCHS, the TAPE IN switch, and the PFL switches on the input channels. When the installation is ready, the message "Your new hardware is installed and ready to use" will appear 12. PHONES JACK Stereo headphones connector. Most of the time, you'll want the output volume from the computer at it's maximum position, but sometimes the default setting is much lower, what makes the output level too low. [. . . ]