User manual JENSEN VOYAGER ANHD20

[. . . ] · Power Supply should disconnected during installation Connect all coax cable connections before connecting +12VDC wire to the wall plate. The switch should be in the OFF position when connecting/disconnecting cables. · All coaxial cable used should be RG-6U for optimal performance · Painting the Antenna is not recommended and may affect performance · Do not use solvents to clean antenna. Use only mild soap and water. AC 24" VENT N O TE: ANTEN NA S HO ULD BE M O UNTED AS CLO SE TO T H E C E N T E R O F T H E R O O F A S P O S S IB L E F O R B E S T R E C E P T IO N . [. . . ] Please note there is a moisture weep hole at the rear of the base. If proper sealing techniques are used (as described in Step 5) you should not need to add additional caulking around the base. NOTE: The Caulking compound used should be approved for the type of vehicle and environment. Check OEM recommendations for your vehicle. Material should be a non-hardening type such as Butyl caulking. F IG U R E 4 3 WALL PLATE INSTALLATION 1. The wall plate/power supply assembly may be mounted in most electrical outlet/switch boxes. The plate can also be mounted without an electrical box. This mounting method requires a hole 2. 75" x 2. 0". Route 2 16AWG wires to this hole from the 12VDC source. Also route all coax cables to this hole. Connect all coax cables to the appropriate wall plate pigtails. Each pigtail has a label for identification. Connect the cable from the roof antenna to the "ANTENNA IN". "RADIO OUT" goes to the input of the AM/FM radio. "CABLE IN" connects to the Park Cable Input. After connecting all coax cables, connect +12VDC wire to the + male spade terminal on the circuit board (marked with a red dot) using a ¼" Insulated Female Spade Terminal. Then connect the ground wire (marked with a black dot) using the same type terminal. Install the wall plate using a two #6 Flat Head screws. Connect main TV to the TV1 output on the front of the wall plate. To Second TV To Antenna To AM/FM Radio To Park Cable ANT ENNA IN TV2 O UT RADIO OUT CABLE IN INTER IO R W ALL 2. 0" 0V GROUND INPUT +12VDC INPUT FIGURE 6 2. 75" #6 FLAT HEAD SCREW R O UTE ALL P O W ER /G R O UND W IRES A ND CO A X CA BLES THRO UG H THIS HO LE FIG URE 5 FIGURE 7 * Recommendation of RG-6U cable type with a maximum length of 10 feet between Plate and Antenna. Select the desired source by moving the switch located on the front of the wall plate. [. . . ] The 7. 5A fuse located on the front of the wall plate protects this receptacle and the power to the roof antenna. If this fuse blows then the antenna will not work. Other wall plates do not have the DC receptacle and are fused at 1 Amp to protect the electronics. ANWP12V 7. 5 AMP MAX DC RECEPTACLE LED INDICATOR 7. 5 AMP MINI ATM FUSE SWITCH TV1 OUTPUT CONNECT TO TV *Warning: Replace Fuse with the same Fuse type & current rating. Failure to do so may cause damage and void warranty. FIGURE 8 SPECIFICATIONS POWER SUPPLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 ­ 16 VDC negative ground at 85mA IMPEDANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 FREQUENCY RANGE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 ­ 850MHz, 500 ­ 1700KHz (AM, FM, VHF, UHF) E-PLANE DIRECTIVITY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Omni-Directional GAIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15dB (typical) GAIN FLATNESS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 5dB (typical) OIP3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80dBmV (typical) OPERATING TEMPERATURE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40C ~ 85C (-40F~ 185F) OVERALL DIMENSIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8"(H) x 12. 75"(W) x 14"(D) Specifications subject to change without notice. [. . . ]