User manual JENSEN VOYAGER JHD905

[. . . ] Before drilling the mounting holes, make sure the area behind the panel where the holes are desired is clear of wires and fuel, vacuum and or brake lines. Mounting Stack Mounting machine screw Bracket metal Vehicle mounting surface Washer Self-Tapping Screws (Hole size 7/32") Machine Screws with Nuts (Hole size 7/32") Nut Attaching the Radio Once the bracket is securely mounted, use the four included M4 machine screws to fasten the bracket to the back of the radio. Alternately, the radio can be mounted directly to the instrument panel if access to the rear of the instrument panel is available. Do not over tighten the 4 mounting screws. Hand tighten only. Regular Mounting Overhead Mounting 4 JHD905 Wiring The wiring diagram depicts all the wiring connections required for proper operation of the unit. Antenna Connector (Black Wire) 9-Pin Connector (Male) NOTE: Do not connect the red wire to a constant power connection. [. . . ] Press and hold VOL+ or VOL- for more than one second to continuously adjust the volume level until the button is released. The current volume level (0 to 40) will appear in the display when the volume is adjusted, returning to the default display three seconds after the adjustment is complete. 8. Setting the Clock To set the clock to display the current time, press the DISP button (3) for more than three seconds to enter clock setting mode, and the time will flash in the display. Press TUN- (8a) to adjust the hours or TUN+ (8b) to adjust the minutes. When no adjustment is made for ten seconds, the time will be set and normal operation will resume. 9. Audio and Menu Adjustment Audio Adjustment Press AUDIO/MENU (9) momentarily to step through the following audio adjustment options: Bass, Treble and Balance (left to right). When the desired option appears in the display, press VOL+ (7a) or VOL- (7b) to adjust that audio feature. When no adjustments have been made for three seconds, the unit will resume normal operation. Menu Adjustment Press the AUDIO/MENU button (9) for more than three seconds to enter menu adjustment mode and adjust any of the menu options. When the desired option appears in the display, press VOL+ (7a) or VOL- (7b) to adjust that option. When no adjustments have been made for three seconds, the unit will resume normal operation. The following menu options may be adjusted using this feature: · · · · · · · Beep Confirm (On or Off) - Determines if a beep will be heard each time a button is pressed. Operation Region (USA or Euro) - Selects the appropriate operating region. Clock Display (12 or 24) - Selects a 12-hour or 24-hour clock display. Display Brightness (Low, Mid or High) - Determines brightness level of the display. Backlight Color (Amber or Green) - Determines the backlight color of the unit. Turn On Volume (0-40) - Selects desired volume level for the unit to assume when turned on. WB Alert (On or Off) - Determines if the weather band alert feature is activated. 7 JHD905 Tuner Operation 10. Select a Band Press AM/FM (10) momentarily to directly access tuner mode from any other function mode. When the unit is already in tuner mode, briefly press AM/FM to change between two AM bands (AM1 and AM2) and three FM bands (FM1, FM2 and FM3). NOTE: If the unit is programmed for European operation, the sequence will be MW1, MW2, FM1, FM2 and FM3. 11. Manual Tuning Press TUN- (11a) or TUN+ (11b) momentarily to tune the frequency one step higher or lower. Press and hold TUN+ or TUN- for more than one second to tune continuously in the selected direction until the button is released. 12. [. . . ] Do not pressure wash directly on the radio. 10 JHD905 Specifications General Power Supply Requirements. . DC 12 Volts, Negative Ground Chassis Dimensions . 131. 6 (W) x 47. 5 (D) x 86 (H) Loading Impedance. . Bass (at 100 Hz), ±10 dB; Treble (at 10 kHz), ±10 dB Current Drain. [. . . ]