User manual JENSEN CD-470C DATASHEET

[. . . ] Check that there will be sufficient space behind the dashboard for the radio chassis. Connect wires prior to actually installing the sleeve. Pigtail wiring should take place after hole size is confirmed. Mount sleeve after wiring. 3) Follow the wiring diagram carefully and make certain all connections of the wiring harness are properly secured and insulated to insure proper operation of this unit. [. . . ] Use the up tuning button to change the option to "AUX-Y". To disable this feature, use the up tuning button to change back to "AUX-N". To exit, press AUDIO ADJUST again or the configuration menu time out (takes about five seconds). Note: If this feature is disabled, the front panel jack will also be disabled. 2 JHD1000 Wiring Low 530 87. 9 5900 531 87. 50 144 6200 1629 108. 00 288 1629 108. 0 1629 90. 0 1600 108. 0 1620 107. 9 SEE PAGE 4 FOR LOW LEVEL AUDIO INPUT DIN CONNECTOR Configuration (continued) High 1710 107. 9 5kHz 9kHz 50kHz 9kHz 9kHz 100kHz 9kHz 100kHz 10kHz 100kHz 10kHz 200kHz 9kHz 50kZHz From 9-Pin Harness 2-Bond Pair PINK (TRIGGER) - SEE CHART C Country Code 10kHz 200kHz Country Band Step The wiring diagram depicts all the wiring connections required for proper operation of the unit. 11 North America AM FM 12 Europe SW AM FM LW 531 87. 5 522 76. 0 530 88. 0 530 87. 9 531 87. 5 1602 108. 0 13 Pacific AM FM 14 Japan AM FM 15 Latin America AM FM TO ANTENNA 16 Brazil AM FM Wiring Color Codes 2-Bond Pair 21 Saudi Arabia AM FM Configuration of the World Band Tuner *SPEAKER WIRES ARE BONDED PAIRS NEGATIVE GRAY WIRES PAIRED WITH RESPECTIVE POSITIVES *SOLDER AND TAPE ALL SPLICES 9 PIN CABLE CONNECTOR BLACK/WHITE (GROUND) GREEN/WHITE (BATTERY +12V) - SEE CHART A ORANGE/WHITE (ACC. +12V) - SEE CHART B 4 PIN CABLE CONNECTOR Press AUDIO ADJUST for more than three seconds. The unit will enter the general configuration menu. To enter the tuner configuration menu, press preset 4, then preset 2. "CC--**" will appear on the display (where ** can equal 11, 12, 14, 15, 16 or 21). Use the up tuning button to select the proper country code for the region of interest. To exit, press AUDIO ADJUST again or the configuration menu time out (takes about five seconds). From 4-Pin Harness 2-Bond Pair 2-Bond Pair Gray Gray/White Orange/White Black Pink Green/White Gray Gray/Blue Gray Gray/Yellow Gray Gray/Red Left Front (-) Left Front (+) Ignition Chassis Ground 12V Out 100mA Memory Right Front (-) Right Front (+) Right Rear (-) Right Rear (+) Left Rear (-) Left Rear (+) Configuration of 2 and 4 Speaker Operation LEFT FRONT SPEAKER RIGHT FRONT SPEAKER Press AUDIO ADJUST for more than three seconds. The unit will enter the general configuration menu. Available modes include radio band and auxiliary input (AUX). 4. Volume Alarm Clock On/Off Selector To adjust the volume, rotate the volume control knob (4) clockwise (to increase volume) or counter clockwise (to decrease volume). This unit has an alarm clock function that can be set to turn the unit on at a specific time. To set the alarm clock, turn the vehicle ignition on and turn the radio off. Press the alarm button (7) for longer than one second, and the time will flash in the display. Press the down tuning button (6b) to adjust the hours or the up tuning button (6c) to adjust the minutes. "A" or "P" will appear on the display to indicate AM or PM. When no adjustment is made for five seconds, the time will be set and normal operation will resume. 5. Sound Adjustment Press AUDIO ADJUST (5) repeatedly to step through the following sound adjustment options: Bass, Treble, Balance (left to right) and Fader (front to rear). When the desired option appears in the display, rotate the volume control knob to adjust that audio feature. When no adjustments have been made for five seconds, the unit will resume normal operation. Press the alarm button momentarily to turn the alarm function on or off. The bell symbol will appear in the display when the alarm function is on. [. . . ] If operating the unit in areas outside North America, the band designation may include LW or SW, and the weather function may be disabled. Recall a Station Select a band (if needed). Press a preset button momentarily, and the unit will tune to the corresponding stored station. Note: Preset buttons will not function in weather band mode. 10. Time/Frequency Selector (T/F) Press T/F (10) to select whether the clock time or radio frequency/playback functions will appear in the display. [. . . ]