User manual JENSEN JISS-600I DATASHEET

[. . . ] The display will automatically return to the normal indication 5 seconds after the last adjustment or when another function is activated. ¢Ý. TREBLE CONTROL Selet the Treble mode by pressing the AUD button ¢Û so theTRE: indication appears on the display panel. Within 5 seconds of choosing the Treble mode, rotate the VOL control ¢Ú counterclockwise to decrease the treble response or clockwise to increase it as desired. The level will be shown on the display panel from a minimum of TRE: -7 to a maximum of TRE: +7 (0 indicates flat response). [. . . ] Pressing and holding the button for longer than 2s will activate the AUTO-STOR(AS)tuning feature which will automatically scan and enter up to 6 local area stations Into the pre-set memories on the band in use. If you have already set the pre-set memories to your favorite stations, activating the auto-store tuning feature will erase those stations and enter the new local ones. This feature is most useful when traveling in a new area where you are not familiar with the local stations. 12 . STATION PRE-SET MEMORIES To set any of the 6 preset memories in each band, use the following procedure: 1. turn the radio on and select the desired band. Select the first station to be pre-set using the TUNE+/-(manual mode )or automatic seek tuning. Press the preset button to be set and continue to hold it in for approximately 2s. -3- -4- OPERATING INSTRUCTIONS The pre-set number (M1-6) will appear on the display panel, indicating that the station is now set into that pre-set memory position. The station can now be recalled at any time by pressing that button. Repeat the above procedure for the remaining 5 presets on that band and for the other 4 bands on the unit. 14 . STATION SCAN SELECTOR(SCAN) Press this button to automatically scan the FM or AM radio band in the upward direction. When a reasonably strong station is detected, the station frequency is displayed for 5 seconds. The time display will return 5 seconds later and will remain until another band and/or frequency is sleceted. The frequency/band display will appear for approximately 5s, and then revert to the time display as before. 22 . AM/FM BAND SELECTOR(BAND) During radio operation, each time this button is pressed, the radio band is changed. The indication AM1. AM2, FM1, FM2 or FM3 will appear on the display panel according to your selection. When FM reception is weak and/or AM1 or AM2 is selected, the stereo (ST) indication will disappear from the display. 23 . MODE SELECTOR (MODE)BUTTON This button is used to select the radio or the TAPE player playback and AUX mode. Each press of the button will select a different mode as indicated on the display panel. -5- -6- SETTING THE CLOCK SETTING THE CLOCK 1. Switch the vehicle ignition and radio "on" . 2. Press and hold the T/F button until the time (hour) display begins to flash. 3. With the hour display flashing, press the TUNE - button to decrement the hours indication, or the TUNE + button to increment the hour indication. 4. Press and hold the T/F button again until the minutes display begins to flash. Adjust the minutes display in the same manner described for the hours indication in step 3. [. . . ] After the initial 90 day period and for a period of 12 months from the date of original purchase, the Company will supply at no charge a replacement for any defective part(s), but will charge for the labor to repair the product. To obtain repair or replacement within the terms of this warranty, the product is to be delivered with proof of warranty coverage (e. g. dated bill of sale), specification of defect(s), transportation prepaid to an approved warranty station, or the Company at the address shown below. This warranty does not extend to the elimination of externally generated static or noise, to the correction of antenna problems, to costs incurred for removal or reinstallation of the product, or to damage to any tapes, speakers, accessories, or electrical systems. This warranty does not apply to any product or part thereof which, in the opinion of the Company, has been damaged through alteration, improper installation, mishandling, misuse, neglect, or accident. [. . . ]