User manual JENSEN TRA4300

[. . . ] It should be connected to a vehicle connection with switched power, such as IGN or ACC. 3A Fuse Left Speaker + (White) Accessory (Red) Left Speaker (White/Black) Ground (Black) Right Speaker + (Gray) Right Speaker (Gray/Black) 5 JHD905 Basic Operation 1. Power Press the power button (1) momentarily to turn the unit on or off. This button is also used to access the software version number. To briefly display the software version on the LCD, press and hold the power button for more than five seconds. 2. [. . . ] When the audio output is silenced, "MUTE" will appear in the display. If the mute feature is activated when the unit is turned off, the volume will default to the programmed turn-on level when the unit is turned back on. 3. Display Press DISP (3) momentarily to toggle the LCD display between function mode (showing tuner, auxiliary input or weather band information, depending on which mode is currently activated) and clock mode (showing the time). 4. Liquid Crystal Display The Liquid Crystal Display (LCD) panel (4) displays the frequency, time and activated functions. Basic Operation 1 2 3 4 JENSEN 5a 6 MUTE DISP AM/FM AUX WB TIMER 7a 8a JENSEN HEAVY DUTY VOL+ TIMER AM TUN AUDIO MENU VOL- TUN + 9 8b 7b AU X SEEK SEEK AM/FM/WB RECEIVER JHD905 + 1 2 3 4 5 6 IN 5b 6 JHD905 5. Auxiliary Input Function To connect a portable audio device (MP3 player, iPOD, etc. ) to the JHD905, connect the headphone or line level output of the device to the 1/8" auxiliary input jack of the JHD905 (5b) using the audio patch cord (included). Press AUX (5a) to select auxiliary input mode. 6. Timer Press TIMER (6) momentarily to directly access timer mode. Briefly press TIMER to start the timer function, and the "TIMER" icon will flash in the display. Press TIMER again to stop the timer, and the "TIMER" icon will remain in the display (without flashing). Press the button again briefly to resume the timer, or press and hold it for three seconds to reset it to zero and to remove the "Timer" icon from the display. 7. Volume Briefly press VOL+ (7a) or VOL- (7b) to adjust the volume up or down one step. Seek Tuning Press SEEK- (12a) or SEEK+ (12b) momentarily to automatically tune the frequency down or up to the next strong station. Radio and Weather Band Operation 10 14 JENSEN MUTE DISP AM/FM AUX WB TIMER JENSEN HEAVY DUTY VOL+ AUDIO MENU VOL- 11a TUN AM TUN + 11b SEEK CH2 SEEK AM/FM/WB RECEIVER JHD905 + 1 2 3 4 5 6 AU X IN 13 8 12a 12b JHD905 13. Preset Stations Six numbered preset buttons (13) store and recall stations for each AM and FM band. To store a station, select a band (if needed) and then select a station. The current station will be stored, and the corresponding preset number will appear in the display. To recall a station, select a band and then press a preset button. The unit will automatically tune to the corresponding stored station. NOTE: Preset buttons recall channels 1-6 on weather band and cannot be set by the user. Weather Band Operation 14. Accessing the Weather Band Press WB (14) to directly access the weather band mode from any other function mode. What is the NOAA Weather Radio? This is a nationwide system that broadcasts local weather emergency information 24 hours a day. network has more than 530 stations covering the 50 states as well as the adjacent costal waters, Puerto Rico, the U. S. Each local area has its own transmitting station and there are a total of seven broadcasting frequencies used: 162. 400MHz (CH1), 162. 425MHz (CH2), 162. 450MHz (CH3), 162. 475MHz (CH4), 162. 500MHz (CH5), 162. 525MHz (CH6) and 162. 550MHz (CH7). How many stations can I expect to receive? Since the broadcasts are local weather and information, the transmission power is usually very low (much less than AM or FM stations) so you will usually receive only one station unless you are on the edge of two or more broadcast signals. The most you will receive will be two or three, and that is rare. Is it possible I won't receive any stations? Depending on location, it's possible you will receive a very weak signal or none at all. [. . . ] The most you will receive will be two or three, and that is rare. Is it possible I won't receive any stations? Depending on location, it's possible you will receive a very weak signal or none at all. Also, similar to AM and FM signals, weather band signals are subject to surrounding conditions, weather, obstructions of the signal by hills or mountains, etc. If no NOAA signals are found/received, the "NO SIG" icon will flash in the display and the tuner will scan all seven NOAA frequencies every 30 seconds. How will I know I am tuned to the weather band? When you select the weather band, the "WB" icon will appear on the display panel, along with the current channel indication. Press TUN+ (11b) or TUN- (11a) to tune to each of the seven channels until you find the weather band station broadcasting in your area. NOAA Weather Alert The Weather Alert function adds an additional level of user safety by automatically switching from the current function mode to weather band mode for a minimum of 60 seconds if a NOAA warning tone (1050 Hz) is received/detected. [. . . ]