User manual JENSEN VOYAGER ACC56M

[. . . ] lnstallation and Wiring Precautions REAR BOTTOM FRONT TRANSPORT LOCK SCREWS (2 RIGHT SIDE, 1 LEFT SIDE) Installation Parts Bracket(L) Bracket(R) Hexagonal bolt with washer (M5 x 10) Screw (C) phillips Head Self-Tapping Screw (T3 x12) 1. To prevent a short-circuit, °<Be sure to turn off the ignition and remove the negative (-) battery cable, prior to installation. NOTE: If the changer is to be installed in a vehicle that is equipped with an on-board drive or navigation computer, do not disconnect the battery cable. If the cable is disconnected, 5 the computer memory may be lost. [. . . ] Anti-vibration springs position PROCEDURE FOR VERTICAL INSTALLATION NOTE: If the anti-vibration spring position has been changed and verified for vertical mounting (as shown on page 6), start with step 2. £A Set the 4 anti-vibration springs to position "v" £B Attach bracket (L) and bracket (R) to each side of the unit, using the hexagonal bolts with washer base (M5 x 10). NOTE: Use seals(A) to cover unused mounting holes on sides of unit. Bracket (L) NOTE: Use seals (A) to cover unused mounting holes on sides of unit. Bracket (R) Hexagonal bolt with washer base (M5 x 10) position "v" Bracket (L) Bracket (R) Hexagonal bolt with washer base (M5 x 10) £C Determine the mounting location, and drill four mounting holes. £D Mount the unit in place, using four self-tapping screws (T5 x 12). Use RTV(silicone sealer) on screw threads or around the holes to prevent moisture intrusion. Self-tapping screw (T5 x 12) £B Determine the mounting location, and drill four mounting holes. Never mount the unit near the fuel tank. Drill holes 4mm in diameter. £C Secure the unit in place, using four self-tapping screws(T5x12). Use RTV(sillicone sealer)on screw threads or around the holes to prevent moisture intrusion. Self-tapping screw (T5 x 12) Bracket (L) Bracket (L) Bracket (R) Drill holes 4mm in diameter. Bracket (R) 6 7 PROCEDURE FOR 45°£ ANGLE INSTALLATION NOTE: If the anti-vibration spring position has been changed and verified for 45°£angle mounting (as shown on page 6), start with step 2. OVERALL WIRING VIEW This page is provided to give you a quick look at the entire wiring of the ACC56M. Use it to plan your wire routing paths and possible connection points. Detailed wiring is explained in the following pages. £A Set the 4 anti-vibration springs to position "45°" £B Attach bracket (L) and bracket (R) to each side of the unit, using the hexagonal bolts with washer base (M5 x 10). position 45°£± ° ° EXISTING RADIO ANTENNA SOCKET Bracket (L) Bracket (R) Hexagonal bolt with washer base (M5 x 10) AQUATRONICS OR VOYAGER CDC READY RADIO DATA CABLE (15 FEET) £C Determine the mounting location, and drill four mounting holes. £D Mount the unit in place, using four self-tapping screws (T5 x 12). Use RTV(silicone sealer) on screw threads or around the holes to prevent moisture intrusion. Self-tapping screw (T5 x 12) NOTES: °<When routing wires and cables from the changer to the radio, it is best to conceal the wires. °<It may be necessary to press the RESET button on the face of the radio the first time after the ACC56M is lnstalled. This will causethe radio to "recognize" that the ACC56M is connected. Bracket (R) 10-DISC COMPACT DISC CHANGER ACC56M Never mount the unit near the fuel tank. Drill holes 4mm in diameter. Bracket (L) 8 9 HINTS FOR CORRECT AND SAFE OPERATION This CD Changer is designed to be operated only on 12 volt DC negative ground systems. The unit cannot be used on 24 volt or positive ground systems. Temperature The unit may not operate correctly in extremely hot or cold temperatures. It is equipped with a built-in thermal protection circuit which will stop operation of the unit when the temperature reaches the preset level. If this should happen, the unit will resume operation when the vehicle returns to a normal temperature range. Remove the magazine from the unit when it is not being used during hot weather. If the CD changer is not used for long periods of time, remove the compact discs from the magazine, and store them in their cases. Condensation Moisture can condense on the laser lens of the CD changer during rainy and humid days, If this should happen the unit will not operate correctly. [. . . ] Inserting a 3" disc into the magazine, either with or without a 3"disc adaptor, can damage the changer and the disc. Such damage will not be covered by the Warranty on this product. °< For additional CD magazines, you may contact us at www. asaelectronics. com Fig. 1 Loading The Magazine Into The Changer Completely slide the door on the changer to the right as shown in Figure 4. [. . . ]