User manual JENSEN VOYAGER AOM-7694

[. . . ] Under these conditions, use extra caution during installation not to cause a short circuit. Do not install the unit in the following locations. °<Locations exposed to direct sunlight. °<Where hot air is discharged from the car heater. [. . . ] Changer must be mounted as explained on the following pages. INSTALLATION The ACC56M changer is designed for horizontal (flat), vertical (upright) or 45-degree mounting. It must never be mounted upside-down or on either one of it's sides as explained previously. The position of the built-in anti-vibration springs (left and right side), must correspond to the mounting position chosen. If the springs are not set correctly for the type of installation chosen, the anti-vibration compensation will not be effective and vibration may cause the disc to skip. CAUTION: After setting the built-in anti-vibration springs, place the supplied Seals (B) over the holes. These seals are used to keep dust, which could cause a malfunction, out of the unit. HORZONTAL INSTALLATION Set the 4 anti-vibration springs to position H°± ° position H°± ° VERTICAL INSTALLATION Set the 4 anti-vibration springs to position V°± ° 45°£ NGLE INSTALLATION A Set the 4 anti-vibration springs to position° 45°£± ° position 45°£± ° ° position V°± ° 4 5 PROCEDURE FOR HORIZONTAL INSTALLATION £AAttach bracket (L) and bracket (R) to each side of the unit, using the hexagonal bolts with washer base (M5 x 10). Anti-vibration springs position PROCEDURE FOR VERTICAL INSTALLATION NOTE: If the anti-vibration spring position has been changed and verified for vertical mounting (as shown on page 6), start with step 2. £A Set the 4 anti-vibration springs to position "v" £B Attach bracket (L) and bracket (R) to each side of the unit, using the hexagonal bolts with washer base (M5 x 10). NOTE: Use seals(A) to cover unused mounting holes on sides of unit. Bracket (L) NOTE: Use seals (A) to cover unused mounting holes on sides of unit. Bracket (R) Hexagonal bolt with washer base (M5 x 10) position "v" Bracket (L) Bracket (R) Hexagonal bolt with washer base (M5 x 10) £C Determine the mounting location, and drill four mounting holes. £D Mount the unit in place, using four self-tapping screws (T5 x 12). Use RTV(silicone sealer) on screw threads or around the holes to prevent moisture intrusion. Inserting a 3" disc into the magazine, either with or without a 3" disc adaptor, can damage the changer and the disc. Such damage will not be covered by the Warranty on this product. HANDLING THE DISCS Dirt, dust, scratches and warpage cause sound skips during playback and a deterioration of sound quality. To take proper care of your discs: 1. Use compact discs that have the logo. 2. Fingerprints and dust should be carefully wiped off the disc's signal surface(glossy side)with a soft cloth. Unlike conventional records, the compact disc has no grooves to collect dust and microscopic debris, so gently wiping with a soft cloth should remove most particles. Wipe in a straight motion from the inside to the outside of the disc. Small dust particles or light stains will have absolutely no effect on reproduction quality. 3. Never use such chemicals as record sprays, antistatic sprays or fluids, benzine or thinner to clean compact discs. Such chemicals could irreparably damage the disc's plastic surface. 4. Discs should be put back in their cases after use to avoid serious scratches that could cause the sound to skip. 5. Do not expose discs to direct sunlight, high humidity, or high temperatures for extended periods of time. Long exposure to high temperatures can warp the disc. [. . . ] Removing The Magazine From The Changer The magazine can be removed from the changer using one of two methods as outlined below in steps 1 and 2. NOTE: Be sure to keep the door on the changer closed at all times when not loading or removing the magazine. Leaving the door open could allow dust, dirt and moisture to enter the changer which could cause the unit to malfunction. 1. During normal operation with power applied, slide open the door on the changer and press the eject button as shown in Figure 6. [. . . ]