User manual JENSEN VOYAGER JCD3006

[. . . ] JCD3006 MOBILE CD PLAYER / RECEIVER Installation and Operation Manual JCD3006 JCD3006 SAFETY INFORMATION When Driving Keep the volume level Iow enough to be aware of the road and traffic conditions. When Washing your Vehicle Do not expose the product to water or excessive moisture. Moisture can cause electrical shorts, fire or other damage. When Parked Parking in direct sunlight can produce very high temperatures inside your vehicle. [. . . ] Carefully unsnap the plastic trim ring from the front of the new radio chassis. Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio. Select a position where the screw Screws holes of the bracket and the screw holes of the main unit Dashboard are aligned (are fitted). Tighten the screws at 2 places on each side. Do not Factory exceed M5 x 9 MM maximum Mounting screw size. Longer screws Bracket may damage components Hook (Remove) inside the chassis. Wire the new radio to the vehicle as outlined in the Universal Installation instructions. Mount the new radio assembly to the dashboard or center console using the reverse procedure of step 1. 4. 5. NOTE: The mounting box, outer trim ring, and half-sleeve are not used for method B installation. Reconnect Battery When wiring is complete, reconnect the battery negative terminal. Detachable Control Panel (DCP) Removing the Detachable Control Panel (DCP) 1. Attach the panel at the right side first, with point B on the main unit touching point A on the DCP (as shown in the diagram). Press the left side of the DCP onto the main unit until a "click" is heard. PANEL RELEASE BUTTON 2 A CAUTION: 1 B · DO NOT insert the DCP from the left side. · The DCP can easily be damaged if dropped or subjected to a strong shock. When the release button is pressed and the DCP is unlocked, the vehicle's vibrations may cause it to fall. To prevent damage to the DCP, always store it in a protective case after detaching it. · The rear connector that connects the main unit and the DCP is an extremely important part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc. · If the DCP is dirty, remove debris with a soft, dry cloth only. You can use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the DCP. 4 JCD3006 WIRING 688A ANTENNA JACK FUSE ANTENNA SOCKET 20-PIN AUDIO/POWER HARNESS (See Figure 1) REAR LINE OUT GREY WHITE L-CH RCA-TO-RCA CABLE (not supplied) RED R-CH AMP Figure 1: 20 PIN HARNESS PIN CHART 1 BLUE 2 12 3 13 4 14 5 15 6 16 7 17 8 18 9 19 10 20 Power Antenna Connect to power antenna or amplifier, If not used, tape bare end of wire. Ground Connect to ground terminal or clean unpainted metal part of chassis. 11 BLACK YELLOW Memory / Battery Connect to battery or 12 volt power source that is always live. The radio will not work if this wire is not connected. Accessory / Ignition Connect to existing radio wire or radio fuse. RED LEFT FRONT WHITE-BLACK LF- RIGHT FRONT GREY-BLACK RFGREY RF+ PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 WIRE COLOR GREY / BLACK GREY VIOLET VIOLET/BLACK EMPTY GREEN GREEN / BLACK RED BLACK RED WHITE WHITE / BLACK EMPTY BLUE YELLOW BLACK EMPTY EMPTY EMPTY WHITE FUNCTION / LABEL RIGHT FRONT SPEAKER ( ) RIGHT FRONT SPEAKER (+) RIGHT REAR SPEAKER (+) RIGHT REAR SPEAKER ( ) N/A LEFT REAR SPEAKER (+) LEFT REAR SPEAKER ( ) IGNITION (ACC) REAR PRE-AMPLIFIER LINE OUT COMMON RIGHT REAR PRE-AMPLIFIER LINE OUT LEFT FRONT SPEAKER (+) LEFT FRONT SPEAKER ( ) N/A POWER ANTENNA BATTERY (+) CHASSIS GROUND N/A N/A N/A LEFT REAR PRE-AMPLIFIER LINE OUT WHITE LF+ LEFT REAR GREEN-BLACK LR- RIGHT REAR VIOLET-BLACK RR- GREEN LR+ VIOLET RR+ 5 JCD3006 BASIC OPERATION 3 7 4 Display (D) 22 19 2 Press the D button (18) on the control panel (or the DISP button on the remote control) to view the clock. The LCD will display the clock for 5 seconds, then return to the previous display mode. [. . . ] Play/Pause Disc Playback (1/PAU) Press the 1/PAU button (12) to suspend disc play. Press the 1/PAU button again to resume disc Play. Intro Scan (2/INT) Press the 2/INT button (13) on the control panel (or the 2/SCN button on the remote control) to play the first 10 seconds of each track sequentially. Press 2/INT again to stop Intro Scan and resume normal play at the current track. [. . . ]