User manual JENSEN VOYAGER JCD3010

[. . . ] JCD3010 MOBILE CD PLAYER / RECEIVER Installation and Operation Manual JCD3010 JCD3010 SAFETY INFORMATION When Driving Keep the volume level Iow enough to be aware of your surroundings. When Washing your Vehicle Do not expose the product directly to water, as this can cause electrical shorts, fire or other damage. When Parked Exposure to direct sunlight for an extended period of time can produce very high temperatures inside the mobile unit. Give the interior a chance to cool down before starting playback. [. . . ] If the unit does not operate, recheck all wiring until the Removing the Unit To remove the radio after installation, insert the removal keys straight back until they click, and then pull the radio out. If removal keys are inserted at an angle, they will not lock properly to release the unit. Removal Key Reconnect the Battery When wiring is complete, reconnect the battery negative terminal. 2. 3. 4. 6. 3 JCD3010 WIRING A- A SHOWN FROM PIN VIEW 15A FUSE A-A Wire Connector ACCESSORY/IGNITION (+) Connect to existing radio accessory fuse or +12 VDC switched power source. POWER ANTENNA Connect to power antenna or amplifier. If not used, tape bare end of wire. MEMORY/BATTERY (+) Connect to battery or 12 volt power source that is always live. The radio will not work if this wire is not connected. GROUND Connect to ground terminal or clean, unpainted metal part of chassis. 4 JCD3010 BASIC OPERATION 1 12 7 3. Press MODE again to cancel Aux In mode and return to previous mode. Reset 6 5 21 4 19 3 2 After releasing the control panel, use a pencil or any non-metallic object to press and hold the RESET button (17) for five seconds to reset the main unit. The unit will return to the factory default settings. The reset button should be activated for the following reasons: · · · initial installation of the unit when all wiring is completed function buttons do not operate error symbol on the display 9 17 JCD3010 10 13 Audio Menu Press the AUDIO button (4) on the control panel (or the S button on the remote control) to access the Audio Menu. You can navigate through the Audio Menu items by pressing the AUDIO (or S) button repeatedly. Once the desired menu item appears on the display, adjust that option by turning the AUDIO control (or pressing the VOL /\ or VOL \/ buttons (24) on the remote control) the within 5 seconds. The unit will automatically exit the Audio Menu after five seconds of inactivity. The following menu items can be adjusted. Volume Level Use the button to adjust the Volume level from "00" (lowest) to "100" (highest). Bass Level 1 VOL S 11 14 15 22 16 8 18 20 Power On/Off ( ) Press the button (1) to turn the unit ON or OFF. Volume Control To increase the volume, turn the AUDIO control (4) clockwise. To decrease the volume, turn the AUDIO control counter-clockwise. If using the remote control, press the VOL /\ or VOL \/ button (24) to adjust the volume. When the volume is adjusted, the volume level is shown on the display panel as a number ranging from 00 (lowest) to 100 (highest). 4 Use the button to adjust the Bass level range from "-10" to "+10". Treble Level Use the button to adjust the Treble level range from "-10" to "+10". Balance 24 VOL 19 18 21 15 LOC AMS PEQ D TR. UP 22 5 23 16 6 11 10 14 Use the button to adjust the Balance between the right and left speakers from "10L" (full left) to "10R" (full right). "BAL L=R" represents an equal balance between the right and left speakers. [. . . ] The selected track number will appear on the display. Press and hold the TUNE up button (19) or TUNE down button (18) for >1 second to fast forward or fast reverse through the disc. CD play starts when the button is released. Play/Pause Disc Playback (1/>||) Press the 1/>|| button (9) to suspend disc play. [. . . ]