User manual JENSEN VOYAGER JHD1000

[. . . ] Replace the dashboard trim panel. M O UNTING TA B DE TA ILS C UT AW AY V IEW O F M OU NTING SU RF ACE TO P TA B B END S IDE V IE W U PW A R D 90 ° M O U NTIN G S URF ACE M OUNT IN G S LEEVE Installation (continued) Universal Installation (Using Mounting Sleeve) 1) Remove endcaps and slide the mounting sleeve off of the chassis. If it is locked into position, use the removal tools (supplied) to disengage it. 2) Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully cut or file as necessary until the sleeve slides easily into the opening. Do not force the sleeve into the opening or cause it to bend or bow. [. . . ] Press the up tuning button until "SP--**" appears in the display (where ** can equal 2 or 4). Change this menu item according to the desired setup by using the up tuning button to modify the setting to either "SP-2" or "SP-4". To exit, press AUDIO ADJUST again or the configuration menu time out (takes about five seconds). GRAY (-) GRAY/WHITE (+) GRAY (-) GRAY/BLUE (+) Configuration of Tuner Seek Sensitivity Setting 4 OR 8 OHM 4 OR 8 OHM The scan sensitivity feature is designed to give flexibility during the tuner seek function. The tuner can be configured such that during seek, it will stop on strong stations, ignoring weaker signals. The tuner can also be configured to stop at all weak signals. LEFT REAR SPEAKER RIGHT REAR SPEAKER GRAY (-) GRAY/RED (+) GRAY (-) GRAY/YELLOW (+) To configure the seek sensitivity setting, press AUDIO ADJUST for more than three seconds. The unit will enter the general configuration menu. While in the general configuration menu, press preset 4 and then preset 2. The unit is now in the tuner configuration menu. Press the up tuning button until "SC--**" appears in the display (where ** can equal 00-15). The numbers are set such that at the setting "SC-00", the unit is more sensitive to weaker signals. This means that the seek function will stop at most or all weak signals. At "SC-15", the seek function will stop only at the strong stations. Use the up tuning button to adjust the seek sensitivity of the tuner to a setting that will suit the application. To exit, press AUDIO ADJUST again or the configuration menu time out (takes about five seconds). . 4 OR 8 OHM 4 OR 8 OHM 3 JHD1000 6. Setting the Clock Basic Operation 1. Power Press the power button (1) to turn the unit on or off. 2. Alarm Clock Function Setting the Alarm Clock To set the clock to display the current time, turn the vehicle ignition on and turn the radio off. Press T/F (6a) for more than one second, and the time will flash in the display. Press the down tuning button (6b) to adjust the hours or the up tuning button (6c) to adjust the minutes. "A" or "P" will appear on the display to indicate AM or PM. [. . . ] Also, similar to AM and FM signals, weatherband signals are subject to surrounding conditions, weather, obstructions of the signal by hills or mountains, etc. JHD1000 Radio Operation PUSH POWER AUDIO MODE ADJUST How will I know I am tuned to Weatherband? 10 2 4 6 3 5 T / F HEAVY DUTY AUX IN When you select the weather band, the indication "WTHR" will appear on the display panel, along with the current channel indication: "CH1", CH2", "CH3", "CH4", "CH5", "CH6" or "CH7". Use the up and down tuning buttons to tune to each of the seven channels until you find the weatherband station broadcasting in your area. TUNE BAND TUNE 1 11a 12 9 11b 5 JHD1000 Specifications Corrective Action If the power supply is connected to the vehicle accessory circuits but the engine is not moving, switch the ignition key to "ACC". DC 12 Volts, Negative Ground Chassis Dimensions . 178 (W) x 178 (D) x 50 (H) Loading Impedance . [. . . ]