User manual JETWAY 601TCFR3A

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual JETWAY 601TCFR3A. We hope that this JETWAY 601TCFR3A user guide will be useful to you.

Lastmanuals help download the user guide JETWAY 601TCFR3A.


Mode d'emploi JETWAY 601TCFR3A
Download
Manual abstract: user guide JETWAY 601TCFR3A

Detailed instructions for use are in the User's Guide.

[. . . ] 601TCF USER'S MANUAL M/B For Socket 370 Pentium III Processor NO. G03-601TCR3A Release date: May 2002 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer. TABLE OF CONTENT USER'S NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii MANUAL REVISION INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 THERMAL SOLUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Please connect it to CDROM CD-Audio output connector. 17 G ND VC C IR X R G ND IR TX 4 1 C D-IN CD Audio-In Headers (12) Wake On-LAN Headers (3-pin) : WOL1 This connector connects to a LAN card with a WAKE ON-LAN output. This connector power up the system when a wake up signal is received through the LAN card. NOTE: This feature requires that BIOS Wake-Up by PCI Card is enabled. WOL1 3 1 WO L G ND 5VSB Wake-On-LAN Headers 2-7 Starting Up Your Computer 1. After all connections are made, close your computer case cover. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V240V or 110V120V depending on your country's voltage used. Connect the power supply cord into the power supply located on the back of your system case according to your system user's manual. Turn on your peripheral as following order: a. Other external peripheral (Printer, Scanner, External Modem etc. . . ) c. For ATX power supplies, you need to turn on the power supply and press the ATX power switch on the front side of the case. The power LED on the front panel of the system case will light. The LED on the monitor may light up or switch between orange and green after the system is on. If it complies with green standards or if it is has a power standby feature. While the tests are running, the BIOS will alarm beeps or additional message will appear on the screen. If you do not see any thing within 30 seconds from the time you turn on the power. The system may have failed on power-on test. Recheck your jumper settings and connections or call your retailer for assistance. Beep One short beep when displaying logo Long beeps in an endless loop One long beep followed by three short beeps High frequency beeps when system is working Meaning No error during POST No DRAM install or detected Video card not found or video card memory bad CPU overheated System running at a lower frequency 6. During power-on, press <Delete> key to enter BIOS setup. Power off your computer: You must first exit or shut down your operating system before switch off the power switch. For ATX power supply, you can press ATX power switching after exiting or shutting down your operating system. If you use Windows 9X, click "Start" button, click "Shut down" and then click "Shut down the computer?" The power supply should turn off after windows shut down. Chapter 3 Introducing BIOS 19 The BIOS is a program located on a Flash Memory on the motherboard. [. . . ] Click PC-HEALTH when Magic Install MENU appears 2. Click NEXT when VIA Hardware Monitor Wizard appears 3. Click Next to install Driver in C:\VIAHM 4. Click Next to use default Program Folders name 4-4-1 How To Use VIA Hardware Monitor Application Software 1. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE JETWAY 601TCFR3A

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual JETWAY 601TCFR3A will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag