User manual JOHN LEWIS JLBICH601

[. . . ] The appliance must not be used as a work surface or as a storage surface. · Only clean this hob in accordance with the instructions. Additions or modifications to the appliance are not per· For cleaning, the appliance must be switched off and mitted. Repairs to the appliance must only be carried out cooled down. [. . . ] Directives: 73/23 - 90/683 (Low Voltage Directive); 93/68 (General Directives) 89/336 (Electromagnetical Compatibility Directive) and subsequent modifications 3 Description of the Appliance Cooking surface layout Single cooking zone 1200W Single cooking zone 1700W Control Knobs Single cooking zone 1700W Residual heat indicator Single cooking zone 1200W 4 Installation Technical Data Appliance dimensions Width Depth Height 590 mm 520 mm 47 mm Cooking rings Position Front left Rear left Rear right Front right Connection voltage Diameter 180mm 145mm 180mm 145mm Power 1700W 1200W 1700W 1200W 230 V ~ 50Hz 5, 8kW Worktop cut-out dimensions Maximum connected load power Width Depth 560 mm 490 mm Electrical Connection 1 This hob must be earthed. Electrical Requirements Any permanent electrical installation must comply with the latest I. E. E. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician, e. g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). It is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm between the switch contacts and of a type suitable for the required load in compliance with the current rules. It is necessary that the yellow / green earth wire is about 2 cm longer than the live and neutral ones. 1 The switch must not break the yellow and Electrical Connection The hob is designed to be connected to 230 V (50 Hz) electricity supply. Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate underneath the hob. For UK only Important After installation and connecting, the cable must be placed so that it cannot at any point reach a temperature of more than 60°C above the ambient temperature. Before the hob is connected, check that the main fuse and the domestic installation can support the load; and that the power supply is properly earthed. The manufacturer disclaims any responsibility should these safety measures not be carried out. 5 Building In 1 The hob must be installed according to the inBuilding In · The dimensions of the cut-out section and recess required must be as shown in the relevant diagrams. · Proper arrangements must be made of a continuous supply of air to the hob to prevent overheating. structions supplied by qualified and competent personnel to the relevant National Standards. · Clean the worktop in the area of the cut-out section. · Stick the one-sided self-adhesive sealing tape supplied all the way round the lower edge of the cooking surface along the outer edge of the glass ceramic panel. The cut ends should lie in the middle of one side. When you have cut it to length (add a few mm), press the two ends flush up against one another. · A protective floor must be installed under the appliance. 6 7 8 The Control Panel Control Knobs The cooking power can be set anywhere between level 1 and 12. 1 12 0 lowest power highest power Off position Residual heat indicator The residual heat indicator lights up, as soon as the corresponding cooking zone is hot. 1 Warning!After Residual heat can be used for melting and keeping food warm. being switched off, the cooking zones need some time to cool down. Look at the residual heat indicator. Selecting the heat setting Heat setting To increase Ring control knob turn clockwise Knob setting 1 - 12 To reduce switch off turn anti-clockwise 0 12 - 1 1. When boiling water/searing food, select a high heat setting. As soon as steam forms or the fat or oil is hot, set a low heat setting. [. . . ] In the event of a fault occurring which you cannot resolve yourself from advice given within this instruction manual your first step is to contact our extended warranty administrators on 0870 0107887 who will give you details for your local Service Force. When contacting Service Force, please quote the model (Mod. ) and serial number (S. N. ), both of which are shown on the rating plate located underneath the hob. So that you always have these numbers at hand, we recommend you to make a note of them here: Mod. : PNC: S. N. : Your hob is covered by a 3 year parts and labour guarantee (see separate details given at point of sale). Please retain your purchase receipt safely for the service engineer to verify the purchase details. . Spare parts This product should be serviced by any authorised service engineer; and only genuine spare parts should be used. [. . . ]