User manual JOHN LEWIS JLDWS1202

[. . . ] JLDWS1202 Dishwasher Instruction manual Dear Customer, Please read this user information carefully and keep it to refer to later. Please pass the user information on to any future owner of the appliance. 1 3 2 The following symbols are used in the text: Safety instructions Warning!Information that affects your personal safety. Information that prevents damage to the appliance. [. . . ] If you want to stop using 3in1 products, please do the following: · Fill up the dispensers for salt and rinse aid again. · Switch the water softener to the highest setting and perform up to three normal cycles without loading any dishes. · Then set the water softener to the water hardness in your area. 20 Selecting the Dishwashing Cycle (Cycle Table) Programme sequence Intermediate rinse Dishwashingcycle Suitable for: Type of soiling Pre-wash Consumption values1) Length (minutes) Energy (kWh) 1, 75 - 1, 95 1, 0 - 1, 5 0, 95 - 1, 05 0, 8 70°Intensive Dinner service and cookware Dinner service and cookware Dinner service and cookware, temperaturesensitive crockery Dishes, excluding saucepans heavily soiled, dried-on food remains, in particular protein and starch 110 - 120 · · · · 90 - 110 Automatic (50° - 65°)2) normally soiled, · dried-on food remains · · · 130 - 160 50°Economy3) normally soiled · · · · · Quick wash (60°)4) just used, lightly to normally soiled - · - · - 30 1) The consumption values were obtained under standardised conditions. They depend on how full the baskets for the dishes are. Variations are therefore possible in practice. 2) When using this cycle the degree of water clouding determines the amount of soiling on the dishes. The length of the cycle and water and energy consumption can vary greatly ­ depending upon the load and how dirty the dishes are. Depending upon the soiling, the temperature of the water will be automatically adjusted to between 50°C and 65°C. 3) Test programme for Test Institutes 4) When using this cycle, only load the dishwasher half full. 9 13 - 15 13 - 25 1 to 2x 23 - 25 2x Water (litres) Main wash Final rinse Drying 21 Starting a Dishwashing Cycle 1. Check that the spray arms can turn freely. The remaining time expected for the cycle will be shown in the multi-display. During the dishwashing cycle, the remaining time shown in the multidisplay may be adjusted according to the size of the load, degree of soiling, etc. A light signal in the form of a dot appears at floor level. If the dishwasher is built in at high level with flush fitting cupboard doors around it, the light signal cannot be seen. The dot shaped light signal is not dangerous. (It is not a laser. ) It lights up while a dishwasher cycle is running and goes out when the cycle ends. 3 3 Interrupting or Cancelling a Dishwashing Cycle Only interrupt a dishwashing cycle that is in progress if it is absolutely necessary. 1 Interrupting the dishwashing programme by opening the dishwasher door Hot steam may escape when the door is opened. Press function buttons 2 and 3 and keep them pressed. The LED indicators of all the buttons that can be selected light up. Exception: The 3in1 button will only illuminate if the function has been activated. The dishwashing cycle has been cancelled. If you want to start a new cycle, check whether there is any detergent in the dispenser. 22 Setting the Delay Timer 3 With the delay timer you can delay the start of a dishwashing cycle for between 1 and 19 hours. [. . . ] In the event of a fault, the safety valve in the water inlet hose immediately interrupts the supply of water to the appliance and the drain pump is activated. In this way water can neither escape nor overflow. The remaining water in the appliance is automatically pumped out. Should a fault occur when the appliance is switched on, a buzzing tone can also be heard. [. . . ]