User manual JOHN LEWIS JLUCLFW6003

[. . . ] JLUCLFW6003 refrigerator Instruction manual Important safety information It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant warnings. These warnings have been provided in the interest of safety. You MUST read them carefully before installing or using the appliance. [. . . ] In this case retain packaging. Ventilation Requirements The appliance must have adequate ventilation to ensure correct operation. Diagram shows the ventilation requirements when installed: A:* Under a worktop, or cupboard. * The clearance space of 10 cm above the appliance may be reduced to 5 cm providing a clearance space 2, 5 cm is left on either side of the appliance. B: When freestanding Cleaning Remove all adhesive tape and packaging, which ensure the accessories do not move in the appliance. Wash the inside of the appliance using lukewarm water and bicarbonate of soda (5ml to 0. 5 litre of water). After cleaning dry the inside of the appliance thoroughly. Location The appliance should be placed in a well ventilated, dry room. The appliance energy use is affected by the ambient temperature. The appliance should therefore: not be installed next to radiators, cookers or other sources of heat only be installed at a location where the ambient temperature corresponds to the climate classification, for which the appliance is designed. Levelling The appliance must be level. Level the appliance by adjusting the two adjustable feet (1) at the front of the appliance. If required the washer (2) can be removed. Climate Classification The climate classification can be found on the rating plate located inside the appliance. The following table shows the ambient temperature for each climate classification: Climate Classification SN N ST Ambient Temperature +10 to +32 °C +16 to +32 °C +18 to +38 °C 2 1 7 Door Reversal If required the opening direction of the door can be changed as follows: To reverse the bottom hinge assembly proceed as follows: Disconnect the appliance from the electricity supply. Tilt the appliance backwards, resting the top edge of the appliance on a stool or something similar. Unscrew the adjustable feet situated on both sides (2 pieces), in addition the screws fixing the lower door holders (3 pieces) respectively the screw on the other side. Take off the freezer door by pulling it slightly downwards. Unscrew the top door hinge pin of the refrigerator then screw it back on the other side. Fit the freezer door on the upper door hinge pin. Put over the pin in the lower door holding plate in the direction of the arrow. Fix the plate on the other side leaving the position of the door unchanged. Then screw in the one screw in the place set free on the other side as well as the adjustable feet (2 pieces) and set up the box. Put over the handles on the other side and put the plastic covering nails supplied in the plastic bag of this instruction book into the holes set free. Put the appliance to its place, set it level and plug it into the mains socket. 8 Electrical connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. WARNING: THIS APPLIANCE MUST BE EARTHED. Should the appliance power supply cable need to be replaced, this must be carried out by a Service Force agent (see page 16). The manufacturer declines any liability should this safety measure not be observed. [. . . ] Defrost water from the cooling plate runs out of the drain and onto a tray on the motor compressor where it evaporates. Droplets of water on the cooling plate during defrosting are quite normal and will freeze on the plate afterwards. When the appliance is not in use External Cleaning Wash the outer cabinet with warm soapy water. There are sharp edges on the underside of the product so care should be taken when cleaning. Once or twice a year dust the condenser (black grille) and the compressor at the back of the appliance with a brush or vacuum cleaner, as an accumulation of dust will affect the performance of the appliance and cause excessive electricity consumption. [. . . ]