User manual JONSERED 455

[. . . ] en pro qu em r is g frereplac ine ba nta eck nded s co Ch me les ion. om un G wer riorat a rec ly NINte mod detiee on era an Us t WARop wear ged. no Do ct to dama or bje d su cke cra Do ct to da bje d or su cke cra G wer riorat a rec ly NINte mod detiee on era an Us t WARop wear ged. no ma r is ine nta en . Co wh led ce iner. [. . . ] Study the operating instructions and safety precautions thoroughly to insure proper functioning of your Grass Catcher and to prevent injury to yourself and others. The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tractor and while mowing. We recommend a wide vision safety mask for over the spectacles or standard safety glasses. UNPACKING INSTRUCTIONS · · Remove all parts and packing materials from carton. Fold flaps to inside of carton and turn carton upsidedown on floor of work area. To protect grass catcher cover during assembly place cover upsidedown on overturned carton. Be sure all parts are there. CARTON CONTENTS: (3) Container Tops (3) Container Bottoms (1) Upper Chute (1) Lower Chute (1) Support Post (1) Mounting Bracket (1) Mounting Support Plate (1) Cover Assembly (1) Cover Seal (1) Bag of Parts (1) Owner's Manual · NOTE: For ease of assembly, aside of your work area, lay out all hardware in the following groups. Each step of the assembly instructions will identify the group needed for that step. BAG OF PARTS CONTENTS ASSEMBLY LOCATION HARDWARE SHOWN ACTUAL SIZE GROUP "A" REAR MOUNTING BRACKET AND SUPPORT PLATE TO DRAW BAR (6) Bolt 7/16 - 14 x 3/4 Self Tapping GROUP "B" SUPPORT POSTS TO COVER ASSEMBLY (2) Bolt 5/16 - 18 x 2-1/4 (2) Bolt 5/16 - 18 x 3/4 (4) Locknut 5/16-18 4 BAG OF PARTS CONTENTS (continued) GROUP "C" SUPPORT POSTS TO MOUNTING BRACKET (2) Retainer Spring (2) Support Clevis Pin (4) Tubing End Caps GROUP "D" LOWER CHUTE ASSEMBLY TO MOWER DECK (2) Latch Hook Assembly (2) Screw #10 x 5/8 (2) Washer, Lock #10 (2) Washer 3/16 x 3/4 x 16 Ga. (2) Nut, Weld #10 GROUP "E" CHUTE LATCH ASSEMBLY to UPPER CHUTE (1) Screw #10 x 1-1/8 (2) Washer 3/16 x 3/4 x 16 Ga. (1) Spacer, Split #10 (1) Nut, Acorn #10 GROUP "F " (1) Rubber Latch CHUTE LATCH ASSEMBLY to LOWER CHUTE (1) Screw #10 x 5/8 (1) Washer, Lock #10 (1) Washer 3/16 x 3/4 x 16 Ga. (1) Nut, Weld #10 5 ASSEMBLY PARTS IDENTIFICATION COVER UPPER CHUTE r is ne ntai en d. Coe wh r. Re cont erlyi ently ent prop qu em r is g frereplac aine k ba d cont Checmende less tion. com un ra re er a INGmow tierio ly on RNerate and de e Us WA t op wear aged. Rotate cover assembly onto its side as shown. Secure support tubes to cover assembly using short hex bolts, long hex bolts, and locknuts as shown. Tighten all hardware securely. COVER ASSEMBLY Fig. 1 SHORT HEX BOLTS MOUNTING BRACKET SUPPORT PLATE HEX BOLTS LONG HEX BOLTS LOCKNUTS LOCKNUTS DRAWBAR THREADED LOWER HOLES SUPPORT POSTS Fig. 4 7 ASSEMBLY 4 · · · · MOUNTING TO TRACTOR (See Fig. 5) Use Hardware - - GROUP "C" 5 · · · CONTAINER ASSEMBLY (See Fig. 6) No hardware required NOTE: For ease of assembly, you may wish to obtain the assistance of another person for mounting assembly to tractor. Raise seat on tractor to allow assembly to be mounted. With cover closed, lift assembly and place support posts into mounting bracket. Allow assembly to rest on bottom of mounting bracket. Line up holes in mounting bracket with holes in support posts and insert support post clevis pins. [. . . ] Failure to do so may result in spontaneous combustion which could develop into a fire. BLADE CARE For best results mower blades must be kept sharp. · See BLADE CARE instructions in your tractor owner's manual. CAUTION: BEFORE PERFORMING ANY MAINTENANCE , SERVICE OR ADJUSTMENTS: Depress clutch brake pedal fully and set parking brake. Place gearshift/motion control lever in "NEUTRAL" position. [. . . ]