User manual JONSERED CL 36 A

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual JONSERED CL 36 A. We hope that this JONSERED CL 36 A user guide will be useful to you.

Lastmanuals help download the user guide JONSERED CL 36 A.

Download

Manual abstract: user guide JONSERED CL 36 A

Detailed instructions for use are in the User's Guide.

 [. . . ] Re cont erlyiently ent prop qu em r is g fre plac aine k ba d re contChec ende less tion. comm un ra re er a INGmow tierio ly on RNerate and de e Us WA t op wear aged. no Do ect to dam or subjked crac

r is ne ntai en d. Coe wh r. Re cont erlyiently ent prop qu em r is g fre plac aine k ba d re contChec ende less tion.  [. . . ] Be sure all parts are there. 

CARTON CONTENTS:
(2) Container Tops (2) Container Bottoms (1) Upper Chute (1) Lower Chute (1) Support Post (1) Mounting Bracket (1) Cover Assembly (1) Cover Seal (1) Bag of Parts (1) Owner's Manual

·

NOTE: For ease of assembly,  aside of your work area,  lay out all hardware in the following groups. Each step of the assembly instructions will identify the group needed for that step. 

BAG OF PARTS CONTENTS
ASSEMBLY LOCATION

HARDWARE SHOWN ACTUAL SIZE GROUP "A"

REAR MOUNTING BRACKET TO DRAW BAR (4) Shoulder Bolt 5/16 - 18 Self Tapping

(4) Bolt 5/16 - 18 x 3/4

(4) Locknut 5/16-18

GROUP "B"
SUPPORT POST TO CONTAINER SUPPORT

(3) Carriage Bolt 5/16 - 18 x 3/4

(3) Locknut 5/16-18

GROUP "C"
SUPPORT POST TO MOUNTING BRACKET

(1) Bracket Support Pin

(1) Retainer Spring (3) Tubing End Caps

4

BAG OF PARTS CONTENTS (continued)
GROUP "D"
(2) Latch Hook Assembly

LOWER CHUTE ASSEMBLY TO MOWER DECK

(2) Screw #10 x 5/8

(2) Washer,  Lock #10

(2) Washer 3/16 x 3/4 x 16 Ga. 

(2) Nut,  Weld #10

GROUP "E"
CHUTE LATCH ASSEMBLY TO UPPER CHUTE

(1) Screw #10 x 1-1/8 (2) Washer 3/16 x 3/4 x 16 Ga. 

(1) Spacer,  Split #10 (1) Nut,  Acorn #10

GROUP "F "

CHUTE LATCH ASSEMBLY TO LOWER CHUTE

(1) Rubber Latch

(1) Screw #10 x 5/8

(1) Washer,  Lock #10

(1) Washer 3/16 x 3/4 x 16 Ga. 

(1) Nut,  Weld #10

5

ASSEMBLY
PARTS IDENTIFICATION
COVER ASSEMBLY UPPER CHUTE DUMP BAG INDICATOR

r is ne ntai en d. Coe wh r. Re cont erlyiently ent prop qu em r is g fre plac aine k ba d re contChecmende less n. m un ratio reco er a INGmow tierio ly on RNerate and de e Us WA t op wear aged. no Do ect to dam or subjked crac

r is ne ntai en d. Coe wh r. Re cont erlyiently ent prop qu em r is g fre plac aine k ba d re contChecmende less n. m un ratio reco er a INGmow tierio ly on RNerate and de e Us WA t op wear aged. no Do ect to dam or subjked crac

CHUTE LATCH

GRASS CATCHER CONTAINERS LOWER CHUTE LOWER CHUTE ATTACHING STRAPS

NOTE: When right hand (R. H. ) and left hand (L. H. ) are mentioned in this manual,  it means when you are seated on the tractor,  in the operator's position. 

THESE ARE THE TOOLS YOU WILL NEED TO ASSEMBLE YOUR GRASS CATCHER:

(1) 3/8" Wrench (1) 1/2" Wrench (2) 9/16" Wrenches (1) 1/2" Socket (1) 9/16" Deep well Socket

(1) Drive Ratchet (1) 3" or longer Extension (1) Short Handle Phillips Screwdriver

CAUTION: BEFORE ASSEMBLING GRASS CATCHER TO TRACTOR: · Depress clutch/brake pedal fully and set parking brake. Assemble support post to container support with the three (3) carriage bolts and locknuts. Tighten securely. 

CARRIAGE BOLTS LANCED TABS TOWARD BOTTOM

FIG. 1C) · Assemble the mounting bracket,  lanced tabs towards bottom,  using the four smaller inside holes on the drawbar. · Install the four bolts and locknuts as shown and tighten securely. 
SUPPORT POST LOCKNUTS

7

FIG. 3

ASSEMBLY

4

MOUNTING COVER ASSEMBLY TO TRACTOR (See Fig. 4) Use Hardware - - GROUP "C"

5
· · · ·

CONTAINER ASSEMBLY (See Fig. 5) No hardware required

NOTE: For ease of assembly,  you may wish to obtain the assistance of another person for mounting assembly to tractor. · Raise seat on tractor to allow assembly to be mounted. · With cover closed,  lift assembly and place support post inside mounting bracket. Allow assembly to rest on lanced tabs of mounting bracket. · Line up holes in mounting bracket with holes in support post and insert bracket support pin. · Install the three (3) tubing end caps onto container support. · Tap each end cap onto container support tubes to seat securely. 
BRACKET SUPPORT PIN COVER ASSEMBLY

Place bottom half inside of top half,  as shown. Place one foot inside bottom half and lift top half to meet bottom half.  [. . . ] CAUTION: BEFORE PERFORMING ANY MAINTENANCE,  SERVICE OR ADJUSTMENTS: · Depress clutch brake pedal fully and set parking brake. · Place gearshift/motion control lever in neutral (N) position. · Place clutch control in "DISENGAGED" position. · Turn ignition key to "OFF" position.  [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE JONSERED CL 36 A

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual JONSERED CL 36 A will begin.