User manual JONSERED LST 42 C-669

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual JONSERED LST 42 C-669. We hope that this JONSERED LST 42 C-669 user guide will be useful to you.

Lastmanuals help download the user guide JONSERED LST 42 C-669.


Mode d'emploi JONSERED LST 42 C-669
Download
Manual abstract: user guide JONSERED LST 42 C-669

Detailed instructions for use are in the User's Guide.

[. . . ] Suspension Arms (2) Left Hand Side Plate Right Hand Side Plate Anti-rotation Bracket Engagement Rod (Not used on some models) Engine Pulley Keeper (Not used on some models) Chute Crank Rod Assembly Support Tube, Crank Rod Lift Handle and Cable Cable Bracket 11. Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times, when using power equipment. Read this owner's manual carefully and know how to operate your snow thrower and how to stop the unit and disengage the controls quickly. [. . . ] Hook the assembly's notched arms onto the two shoulder bolts you assembled to the inside of the tractor frame. Hanger brackets using two pivot lock pins (GG) and 1/8" hairpin cotters (EE). Assemble the short "V" belt onto the engine pulley and then onto the large pulley on top of the clutch/idler assembly. The belt must be placed to the inside of the engine pulley keeper, the idler pulley and the keeper bolt located beside the large pulley. IMPORTANT: Do Not assemble the "V" belt around the outside of the engine pulley keeper or the keeper bolt. Attach the two suspension arms to the rear of the clutch/idler assembly using two 5/16" x 3/4" hex bolts (C), 5/16" washer (Q) and 5/16" nylock nuts (Y) for each arm. Place the arms on the outside of the frame with the notches to the rear. Insert a tensioning chain through the hole shown and attach the end link to the spring on the lower idler arm. Hook the spring from the parts bag through the end of the tensioning chain. Hook the other end of the spring onto the bottom of the bolt and nut which secure the idler pulley to the upper idler arm. Hold the bolt head and assemble a 3/8" hex lock nut (Z) onto the bolt, leaving enough space for the spring to pivot freely between the two nuts. Pace the extra tensioning chain (JJ) through the left front hole in the clutch/idler assembly and then turn the assembly upside down. Two different length drive belts are included with your snow thrower. Use the table below to select the correct drive belt for your type tractor. The part number is printed on the outside of the belt . Set aside the belt that is not for your tractor to avoid accidentally using it. Install the drive belt down between the hex bolt and the flat idler pulley with the flat side of the belt against the pulley. Loop the belt around the large v-pulley, placing it between the v-pulley and the hex bolt next to the pulley. Place the belt to the inside of the other flat idler pulley. Assemble the drive belt onto the engine pulley and then onto the large pulley on top of the clutch/idler assembly. The belt must be placed to the inside of the idler pulley and the keeper bolt located beside the large pulley. Place tension on the belt by pulling the left side tensioning chain out as far as the 3/32" hairpin cotter (FF) will allow. [. . . ] If you replaced the engine pulley keeper on a manual attachment clutch tractor, reinstall the tractor's original engine pulley keeper. See figure 33 on page 17 or figure 39 on page 19. If you have a rod operated attachment clutch, remove the engagement rod from the tractor's clutch arm. If a rear mounted attachment is to be used, remove the rear weight tray, leaving the bolts that you installed in the sides of the tractor draw bar. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE JONSERED LST 42 C-669

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual JONSERED LST 42 C-669 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag