User manual JRC NSVA301

[. . . ] 2004 JRC SAW FILTER NSVA301 Application Cordless telephone Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig. 1. Input and Output Impedance 50 Nominal Center Frequency (f0) 959. 5MHz Insertion Loss 958. 3~960. 7MHz 3. 5dB max. 2. 5dB Response Variation 958. 3~960. 7MHz 1. 5dB max. [. . . ] 2004 IN 50 1 8 7 OUT 50 2 SAW 6 3 4 5 (a) (1) Fig. 1 Measuring circuit 3. 5±0. 2 (b) 3 . 5 ±0 . 2 J4X 59 (3) (0. 95) (2) 4 (0. 8) [5x] (0 . 6 ) 5 (0. 6) [8 x ] 3 Marking (1) Manufacture's Mark (2) Lot Number (a) Year (b) Month *Oct. --- X Nov. --- Y Dec. --- Z (3) Part number Mark Pin no. 1 2 3 4 5 6 7 8 Connection GND IN/OUT GND GND GND OUT/IN GND GND 1 . 0 ±0 . 2 (2 . 54) 2 (1 . 2 7 ) 6 (1. 0) [2 x ] 1 8 7 Fig. 2 Package dimensions (in mm) 4. 3 0. 8 1. 3 [6x] 0. 8 [6x] 4. 3 1. 27 1. 27 Via -Hole( 0. 3) Fig. 3 Desirable land area (in mm) NSVA301 Oct. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -10ºC or more than +60ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max. , the time of soldering: 10 seconds max. , the power of soldering iron: 30W max. . Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. As it might be a cause of degradation or destruction to apply D. C. voltage between each terminal, apply D. C. [. . . ] When intending to use any our product please contact our sales representatives in advance. 3. NSVA301 Oct. 2004 IN 50 O *27nH 11 10 , X , W , U , V OUT 50 O 39pF 12 SAW , P , Q , , T R *27nH , S 0 S21 33pF FREQUENCY CHARACTERISTICS *murata LQW18A series 0 Insertion Loss [dB] 20 2 (1) 13. 30±0. 20 40 (a) (b) (C) (1. 26±0. 13) 4 (2) 60 6 80 100 CH1 : center 959. 5 span 200 CH2 : center 959. 5 span 200 J4Y1 VS971 S11 6. 5±0. 20 8 10 (3) S22 (R0. 3) [4×] Marking (1) Manufacture's Mark (2) Lot Number (a) Year 2. 0 max. (b) Month *Oct. --- X Nov. --- Y Dec. --- Z S11 (0. 76) 11 9 (2. 54) (2. 54) 11S22 9 (c) Date 1 --- 0 -9 10 -19 --- 1 20 -31 --- 2 (3) Part Number Mark VSWR 7 5 3 1 859. 5 Frequency [MHz] VSWR 7 5 3 (2. 54±0. 15) 1059. 5 (1. 4) [12×] Frequency [MHz] Pin No. Connection 1 2 3 4 5 6 7 8 1059. 5 1 859. 5 GND(PKG) GND(PKG) 0 [12 ×] S21 12 1 2 3 4 5 (0. 8) GND(PKG) GND(PKG) OUT/IN GND(signal) GND(PKG) GND(PKG) GND(PKG) GND(PKG) IN/OUT GND(signal) InsertionLoss [dB] 20 40 60 80 100 (2. 54±0. 15) 11 10 9 8 7 6 9 10 11 12 (R0. 3) 0. 3 [12×] 3000 Fig. 2 PackageFrequency [MHz] mm) dimensions(in Insertion Loss [dB] Fig. 1 Measuring circuit [. . . ]